Abstract:Improving the toughness of epoxy resins (EP) with diverse thermoplastic polymers through curing reaction induced phase separation (RIPS) has been widely studied, with the prerequisite of designing and tailoring the phase morphology evolution of the blend. Herein, two typical amine-type curing agents, 4,4′-diamino diphenylmethane (DDM) with precuring temperature at around 150 °C and diethylenetriamine (DETA) at 80 °C were utilized to regulate and control the phase structures of EP-poly(ε-caprolactone) (PCL) blends. The curing temperature above or below the melting temperature (Tm) of PCL resulted in different states of PCL. The effect of curing temperature on the miscibility between EP matrix and PCL phase, and the correlation between phase morphology evolution and thermomechanical behavior, mechanical properties were comprehensively investigated for the first time. Results revealed that when the curing temperature of EPDDM-PCL blends was higher than the Tm of PCL, curing took place without phase separation; while distinct phase separation took place when EPDETA-PCL was cured at a temperature below the Tm of PCL. When the curing temperature was high, the PCL was able to dissolve completely in the resin before crosslinking began, so that semi-interpenetrating networks were formed; and that when the curing temperature was low, the PCL was unable to dissolve, and therefore formed separate particles. Consequently, the EPDDM-PCL blends exhibited all-leading mechanical properties due to the entanglement and slippage between PCL chains and EP networks. The strength of EPDETA-PCL was reduced but the toughness was improved for island-shaped PCL particles bridging or pinning the cracks during failure. These results elucidated the effect of the phase morphologies formed at different curing temperature on mechanical properties, and provided significant insights regarding the toughening of thermosets.

Study on Dynamically Cured PP/PP-g-MAH/Talc/Epoxy Composites

The Curing Behavior and Properties of Diglycidyl Ether of 4,4′-Bis(4-hydroxybenzoyloxy)-3,3′,5,5′-tetramethylbiphenyl and Its Composites with Multi-Wall Carbon Nanotubes

STUDY ON DGE-BHBTMBP/E-51/DDS CURED

A Comparative Study of Epoxy Resin Cured with a Linear Diamine and a Branched Polyamine

Study on the Curing Behavior of Polythiol/phenolic/epoxy Resin and the Mechanical and Thermal Properties of the Composites

Mechanical Properties and Thermal Behaviors of Dynamically Photocrosslinked PP/EPDM Blends

Studies on the curing behavior, thermal, and mechanical properties of epoxy resin‐co‐amine‐functionalized lead phthalocyanine

Mechanical properties, morphological structure, and thermal behavior of dynamically photocrosslinked PP/EPDM blends

Dynamic and static mechanical properties of PP/EVA blend nanocomposites: Effects of type of masterbatch preparation technique and nature of compatibilizer

Dynamic Mechanical Properties and Thermal Effect of an Epoxy Resin Composite, Encapsulation’s Element of a New Electronic Component

Chemical treatment on polypropylene (PP)/recycled acrylonitrile butadiene rubber (NBRr)/banana skin powder (BSP) composites using epoxy resin

A new strategy to improve the toughness of epoxy thermosets by introducing the thermoplastic epoxy

Preparation and Characterization of Composites: Ethylene–propylene–diene Terpolymer‐graft‐maleic Anhydride/caco3

Epoxidized natural rubber toughened polylactic acid/talc composites: Mechanical, thermal, and morphological properties

Experimental Investigation of Polypropylene Composite Drawn Fibers with Talc, Wollastonite, Attapulgite and Single-Wall Carbon Nanotubes

Diatomite‐filled epoxy resin composites: Curing behavior, dielectric, and thermal properties

Effects Of Talcum Powder(Talc) And Compounding Sequence On The Morphology And Mechanical Properties Of Pa6/Pp/Mapp Blend

A comprehensive study on the effect of small rates of walnut shell and talc fillers on the thermal,mechanical, and morphological properties of epoxy hybrid composites

Effects of curing temperature on the structure and properties of epoxy resin-poly(ε-caprolactam) blends

Dynamically photocrosslinking of polypropylene/EPDM blends as a thermoplastic elastomer

Mechanical properties and structural characteristics of dynamically photocrosslinked PP/EPDM blends