Abstract:Increasing the power conversion efficiency (PCE) of kesterite Cu2ZnSn(S,Se)4 (CZTSSe) solar cells has remained challenging over the past decade, in part due to open-circuit voltage (VOC)-limiting defect states at the absorber/buffer interface. Previously, we found that substituting the conventional CdS buffer layer with In2S3 in CZTSSe devices fabricated from nanoparticle inks produced an increase in the apparent doping density of the CZTSSe film and a higher built-in voltage arising from a more favorable energy-band alignment at the absorber/buffer interface. However, any associated gain in VOC was negated by the introduction of photoactive defects at the interface. This present study incorporates a hybrid Cd/In dual buffer in CZTSSe devices that demonstrate an average relative increase of 11.5% in PCE compared to CZTSSe devices with a standard CdS buffer. Current density-voltage analysis using a double-diode model revealed the presence of (i) a large recombination current in the quasi-neutral region (QNR) of the CZTSSe absorber in the standard CdS-based device, (ii) a large recombination current in the space-charge region (SCR) of the hybrid buffer CZTSSe-In2S3-CdS device, and (iii) reduced recombination currents in both the QNR and SCR of the CZTSSe-CdS-In2S3 device. This accounts for a notable 9.0% average increase in the short-circuit current density (JSC) observed in CZTSSe-CdS-In2S3 in comparison to the CdS-only CZTSSe solar cells. Energy-dispersive X-ray, secondary-ion mass spectroscopy, and grazing-incidence X-ray diffraction compositional analysis of the CZTSSe layer in the three types of kesterite solar cells suggest that there is diffusion of elemental In and Cd into the absorbers with a hybrid buffer. Enhanced Cd diffusion concomitant with a double postdeposition heat treatment of the hybrid buffer layers in the CZTSSe-CdS-In2S3 device increases carrier collection and extraction and boosts JSC. This is evidenced by electron-beam-induced current measurements, where higher current generation and collection near to the p-n junction is observed, accounting for the increase in JSC in this device. It is expected that optimization of the heat treatment of the hybrid buffer layers will lead to further improvements in the device performance.

Over 9% Efficient Kesterite Cu2ZnSnS4 Solar Cell Fabricated by Using Zn1–xCdxS Buffer Layer

Sputtering Deposited and Energy Band Matched ZnSnN2 Buffer Layers for Highly Efficient Cd‐Free Cu2ZnSnS4 Solar Cells

Realizing zinc-doping of CdS buffer layer via partial electrolyte treatment to improve the efficiency of Cu2ZnSnS4 solar cells

Over 10% Efficient Cu2CdSnS4 Solar Cells Fabricated from Optimized Sulfurization

ZnO1−xSx Solid Solution as Potential Buffer Layer Materials for Cu2ZnSnS4‐Based Thin Film Solar Cells: Structural and Interfacial Properties

Over 10% Efficiency Pure Sulfide Kesterite Solar Cells on Transparent Electrode with Cd-Ag Co-Alloying

Ag‐Refined Kesterite in Superstrate Solar Cell Configuration with 9.7% Power Conversion Efficiency

Influence of Cd0.6Zn0.4S buffer layer on the band alignment and the performance of CZTS thin film solar cells

Enhanced Efficiency of Cu(In,Ga)Se 2 Solar Cells With a Thin CdS Buffer Layer Via a Zn 0.8 Mg 0.2 O Second Buffer Layer

Cadmium‐Free Kesterite Thin‐Film Solar Cells with High Efficiency Approaching 12%

High-Efficiency Cu(In,Ga)Se₂ Thin Film Solar Cells Using ZnS and CdS Buffer Layers

All-Layer Sputtering-Free Cu2Zn1-xCdxSnS4 Solar Cell with Efficiency Exceeding 7.5%

A Potential Alternative Deposition Technology for CdS Buffer Layer in Kesterite Solar Cells Via Intermittent Photochemical Deposition

Enhancing the properties of Cd-free MgZnS buffer for solar cells by co-sputtering ZnS and Mg targets

Towards a high efficient Cd-free double CZTS layers kesterite solar cell using an optimized interface band alignment

Gradient bandgap enables >13% efficiency sulfide Kesterite solar cells with open-circuit voltage over 800 mV

Enhanced Carrier Collection in Cd/In-Based Dual Buffers in Kesterite Thin-Film Solar Cells from Nanoparticle Inks

Electrical barriers and their elimination by tuning (Zn,Mg)O composition in Cu(In,Ga)S2: Systematic approach to achieve over 14% power conversion efficiency

8.36% Efficient CZTS Solar Cells on Transparent Electrode Via Solution Processing

Boost the efficiency of Cu2ZnSn(S,Se)4 solar cell by using Mn2+ induced ultra‐thin CdS buffer layer

Improvement of the CIGS solar cell performance: structure based on a ZnS buffer layer