Abstract:Reducing production cost to accelerate the industrialization process of thin film solar cells (TFSCs) makes it urgently demanded to elevate the deposition rate and reduce the needed thickness of absorbers in addition to the prerequisite performance improvement. Based on very high frequency plasma enhanced chemical vapor deposition process with a low bombardment energy and large ion flux, ultra-thin, high-deposition-rate, and high-performing hydrogenated microcrystalline silicon (c-Si:H) single- and related hydrogenated amorphous silicon (a-Si:H)/c-Si:H double-junction TFSCs are developed in this study. By tuning various process parameters (silane concentration, power, and pressure), the deposition rates and electrical properties of c-Si:H materials are studied in detail. Device-level c-Si:H intrinsic materials with a deposition rate of 10.57 /s and photosensitivity of 7.54102 can be obtained when depositing with a silane concentration of 9%, a power of 70 W, and a pressure of 2.5 Torr. By further applying device-level high-deposition-rate c-Si:H intrinsic materials in c-Si:H single-junction TFSCs on magnetron-sputtered and wet-etched aluminum-doped zinc oxide (ZnO:Al) substrates with optimized surface morphologies and photoelectrical properties, and by combining advanced device designs, an initial conversion efficiency of 7.49% can be achieved for pin-type ultra-thin and high-deposition-rate c-Si:H single-junction TFSCs (the thickness values of intrinsic layers are 1.1~m). To further improve the conversion efficiency of TFSCs, pin-type a-Si:H/c-Si:H tandem TFSCs are fabricated by using n-a-Si/n-c-Si/n-nc-SiOx:H/p-nc-SiOx:H as the tunnel recombination junctions (TRJs), which, however, have unaddressed issues that the wide band-gap nc-SiOx:H materials with a low conductivity strongly reduce the recombination rate of carriers, thereby resulting in the photo-generated carriers accumulating near the TRJs, weakening the built-in electric field in the top sub-cells and leading to an open circuit voltage (Voc) loss in a-Si:H/c-Si:H tandem TFSCs up to 115~mV far above average values. By simultaneously inserting the p- and n-type narrow-gap c-Si:H materials, which are highly defective and narrower than the band gap of nc-SiOx:H materials, into the TRJs to implement the electrically lossless interconnection between the a-Si:H top and c-Si:H bottom sub-cells, the Voc loss is successfully reduced to 43~mV and an initial efficiency of 12.03% (Voc=1.48~eV, Jsc=11.67~mA/cm2, FF=69.59%) is achieved for ultra-thin pin-type a-Si:H/c-Si:H tandem TFSCs with a total thickness of 1.48~m, thus paving the way for the low-cost production of TFSCs.

15% Efficiency Ultrathin Silicon Solar Cells with Fluorine-Doped Titanium Oxide and Chemically Tailored Poly(3,4-ethylenedioxythiophene):Poly(styrenesulfonate) As Asymmetric Heterocontact

Tuning of the Contact Properties for High-Efficiency Si/PEDOT:PSS Heterojunction Solar Cells

A Facile Interface Engineering Method to Improve the Performance of FTO/ZnO/CsPbI 3− X Br X ( X < 1)/C Solar Cells

Ultra-Thin Film Microcrystalline Silicon with High Deposition Rate and Its Application in Tandem Silicon Solar Cells

Highly Efficient and Highly Flexible Thin Crystalline Silicon Heterojunction Solar Cells Based on Dopant-Free Carrier-Selective Contacts Fabricated with Simple Processes

High-Performance Ultrathin Organic-Inorganic Hybrid Silicon Solar Cells via Solution-Processed Interface Modification.

Realization of 13.6% Efficiency on 20 μm Thick Si/Organic Hybrid Heterojunction Solar Cells via Advanced Nanotexturing and Surface Recombination Suppression

Textured Perovskite/Silicon Tandem Solar Cells Achieving Over 30% Efficiency Promoted by 4-Fluorobenzylamine Hydroiodide

< 50-μm thin crystalline silicon heterojunction solar cells with dopant-free carrier-selective contacts

Silicon/Organic Hybrid Solar Cells with 16.2% Efficiency and Improved Stability by Formation of Conformal Heterojunction Coating and Moisture‐Resistant Capping Layer

High Performance Nanostructured Silicon-Organic Quasi P-N Junction Solar Cells Via Low-Temperature Deposited Hole and Electron Selective Layer.

50-Μm Thick Flexible Dopant-Free Interdigitated-Back-contact Silicon Heterojunction Solar Cells with Front MoOx Coatings for Efficient Antireflection and Passivation.

PEDOT:PSS-Nafion/n-Si Hybrid Heterojunction TOPCon Solar Cells: Experiment and Simulation

High Efficiency Solar Cells As Fabricated by Sb2S3-modified TiO2 Nanofibrous Networks.

Study on the Fabrication of PEDOT:PSS/Si Hybrid Solar Cells Incorporated with F4TCNQ and VTMO

High-efficiency ITO-free polymer solar cells using highly conductive PEDOT:PSS/surfactant bilayer transparent anodes

Performance Enhancement of Thin-Film Silicon Solar Cells by Development of Core Component Layers

Silicon Nanowires Incorporated Efficient and Flexible PEDOT:PSS/Silicon Hybrid Solar Cells

Rapid and low temperature micro inverted pyramid texturing of silicon via copper catalyzed chemical etching for high efficiency PEDOT:PSS/silicon hybrid solar cells

Highly Efficient Organic/Silicon Hybrid Solar Cells with a MoO3 Capping Layer

Enhancing the Selectivity and Transparency of the Electron Contact in Silicon Heterojunction Solar Cells by Phosphorus Catalytic Doping