Abstract:In this paper, the effects of the width of the mold on the surface velocity, flow field pattern, turbulent kinetic energy distribution, and surface-level fluctuation in the mold were studied with measurement of the flow velocity near the surface of the mold at high temperature with the rod deflection method and numerical calculation with the standard k-ε model coupled with the discrete-phase model (DPM) model for automobile exposed panel production. Under the conditions of low fixed steel throughput of 2.2 ton/min, a nozzle immersion depth of 140 mm, and an argon gas flow rate of 4 L/min, as the width of the mold increases from 880 mm to 1050 mm and 1300 mm, the flow velocity near the surface of the mold decreases. The flow direction changes from the positive velocity with the mold widths of 880 mm and 1050 mm to the unstable velocity with the mold width of 1300 mm. The calculated results are in good agreement with the measured results. The turbulent kinetic energy near the submerged entry nozzle (SEN) gradually increases, and the risk of slag entrainment increases. Under the conditions of high fixed steel throughput of 3.5 ton/min, the SEN immersion depth of 160 mm, and the argon gas flow rate of 10 L/min, as the width of the mold increases from 1600 mm to 1800 mm and 2000 mm, the velocity near the mold surface decreases. The flow velocity at 1/4 of the surface of the mold is positive with the mold width of 1600 mm, while the velocities are negative with the widths of 1800 mm and 2000 mm. The calculated results are basically consistent with the measured results. The high turbulent kinetic energy area near the nozzle expands to a narrow wall, and the risk of slag entrainment is significantly increased. In both cases of low and high fixed steel throughput, the change rules of the flow field in the mold with the width are basically the same. The argon gas flow rate and the immersion depth of SEN should be adjusted reasonably to optimize the flow field in the mold with different widths under the same fixed steel throughput in the practical production.

Effects of Different Parameters on Porosity Defects Between the Horizontal and Vertical Shot Sleeve Processes

Numerical simulation and optimization of liquid metal flow in the shot sleeve of cold chamber die casting process

Effects of Process Parameters on Internal Quality of Castings During Novel Casting

Effects of Process Parameters on Shrinkage Porosity in 357 Semi-Solid Die Casting Parts

Numerical simulation of shrinkage porosity defect in billet continuous casting

Effects of Operating Parameters on the Flow Field in Slab Continuous Casting Molds with Narrow Widths

Direct Observation of Filling Process and Porosity Prediction in High Pressure Die Casting

Finite element analysis for die casting parameters in high-pressure die casting process

Study on the Influence of Injection Velocity on the Evolution of Hole Defects in Die-Cast Aluminum Alloy

Numerical Simulation of Influence of Vertical Continuous Casting Process Parameters on Heat Transfer and Mold Stress of C71500 Large Diameter Hollow Ingot

Effect of different processing parameters on interfacial heat-transfer behavior in high-pressure die-casting process

Process Parameter Effects on Solidification Behavior of the Superalloy During Investment Casting

The characterization of porosity and externally solidified crystals in a high pressure die casting hypoeutectic Al-Si alloy using a newly developed ceramic shot sleeve

Effect of Cooling Process on Porosity in the Aluminum Alloy Automotive Wheel During Low-Pressure Die Casting

Effect of Mold Width on the Flow Field in a Slab Continuous-Casting Mold with High-Temperature Velocity Measurement and Numerical Simulation

Influences of Die Casting Parameters on the Porosity in Aluminum Alloy Air-conditioning Compressor Cylinder

Casting Defects of Ti-6al-4v Alloy in Vertical Centrifugal Casting Processes with Graphite Molds

Study on the Effects of the Slow Shot Phase on the Flow Patterns of Die-Casting Mold Filling Process

Numerical Simulation on the Liquid Metal Flow of the Acceleration Phase in the Shot Sleeve of Cold Chamber Die Casting Process

Mechanism and Application of A Newly Developed Pressure Casting Process: Horizontal Squeeze Casting

Influence of Slow-Shot Speed on PSPs and Porosity of AlSi17Cu2.5 Alloy During High Pressure Die Casting