Abstract:Organic additives used in Cu electroplating for IC interconnects have been studied extensively due to their pivotal roles in the void-free filling of recessed features. The suppressive additives are typically polymers or co-polymers with variable molecular weight (MW). The properties of these additives, as well as their interaction with accelerator, vary with the monomer type and the MW. As the additives are typically treated as indivisible molecules in the analysis of the filling mechanism, these variations are typically quantified by the difference in some coefficients that characterize the additive behaviors, such as adsorption / desorption rates and suppression strength. As an example, polyethylene glycol (PEG) with a larger MW would have a higher adsorption rate and exhibit stronger suppression effect than PEG with a smaller MW. However, since these large molecules consist of multiple identical building blocks from the polymerization of one or more monomer species, the behavior of the molecule as a whole depends on the number and type of the monomers. In order to understand such an intrinsic dependency and the resulting differences in additive properties, stochastic modeling was applied in the study of suppressor additive and its interaction with accelerator [1]. Using PEG and SPS as the model chemicals, a stochastic model was developed to simulate the transient processes in Cu electroplating, e.g. cyclic voltammogram (CV) under various conditions. Simulations were performed for both suppressor-only cases and suppressor-accelerator interactions. The dependency of PEG adsorption / desorption and PEG-SPS interaction on various factors, including bath composition, scan rate and molecular weight, was simulated and compared with the corresponding experimental measurements. An overall good qualitative match was shown in the comparisons. Figure 1 shows simulated CVs under two very different conditions. At higher SPS/Cl - concentrations, case (a) demonstrates the PEG-SPS interaction, which has been known to be important for the super-conformal filling of trenches [2, 3]. At lower SPS / Cl - concentrations, case (b) demonstrates the critical desorption behavior of PEG as a suppressor, which has been shown to be important for the fast bottom-up type filling of high aspect ratio TSVs in damascene copper plating [4]. Since the proposed model provides a unified approach to simulate both the suppress-accelerator interaction and the critical desorption behavior of suppressors, it enables the development of general-purpose multi-scale simulation programs for the filling of various recessed features within a wide length-scale range covering both the Damascene interconnects and TSVs. References [1] L. Yang, A. Radisic, J. Deconinck, P. Vereecken, Journal of the Electrochemical Society, 161, D269(2014) [2] A. C. West, S. Mayer, J. Reid, Electrochemical and Solid-State Letters, 4, C50(2001) [3] T. P. Moffat, D. Wheeler, W. H. Huber, D. Josell, Electrochemical and Solid-State Letters, 4, C26(2001) [4] L. Yang, A. Radisic, J. Deconinck, P. Vereecken, Journal of the Electrochemical Society, 160, D3051(2013) Figure 1

Screening of electroplating additive for improving throwing power of copper pyrophosphate bath via molecular dynamics simulation

Potential-Dependence Of Additives Distribution In Copper Electrodeposition Via Filling

Simulation of TSV Copper Electrodeposition Process with Additives

Electrochemical Analysis of Cathode in TSV Copper Electroplating

Thioacetamide Additive Homogenizing Zn Deposition Revealed by In Situ Digital Holography for Advanced Zn Ion Batteries

Deciphering the levelling mechanism of sorbitol for copper electrodeposition via electrochemical and computational chemistry study

A comparison of typical additives for copper electroplating based on theoretical computation

A Research on the Performance of Pyrophosphate Cu-Sn Alloy Electroplating Bath

Computational Chemistry and Electrochemical Studies of Adsorption Behavior of Organic Additives during Gold Deposition in Cyanide-free Electrolytes

Computational Chemistry and Electrochemical Mechanism Studies of Auxiliary Complexing Agents Used for Zn-Ni Electroplating in the 5-5'-Diethylhydantoin Electrolyte

Stochastic Modeling of Organic Additives in Cu Electroplating

Copper Electroplating with Polyethylene Glycol: Part II. Experimental Analysis and Determination of Model Parameters

Visualizing electrochemical zinc deposition and the role of a polymer additive in the crystal growth mechanism

Interactive Effects of Additives and Electrolyte Flow Rate on the Microstructure of Electrodeposited Copper Foils

Toward Preeminent Throwing Power from a Novel Alkaline Copper Electronic Electroplating Bath with Composite Coordination agents

Functional additives inhibit crystal growth to achieve low-roughness and high-peel strength of micro-coarsening copper foil

Screening Ammonium‐Based Cationic Additives to Regulate Interfacial Chemistry for Aqueous Ultra‐Stable Zn Metal Anode

Synthesis of Quaternary Ammonium Salts Based on Diketopyrrolopyrroles Skeletons and Their Applications in Copper Electroplating.

Effect of Additives on Shape Evolution During Electrodeposition

Electrochemical Studies and Molecular Dynamics Simulation of the Interaction between Accelerators and Cu Surface During the Electroplating Process