Abstract:Longitudinal-torsional ultrasonic vibration-assisted milling is a machining method that can effectively improve the quality of the machined surface. When this method is used for the end milling of TC18 titanium alloy, however, the law of influence on the machined surface and subsurface remains unclear. In this study, we examined the effects of the ultrasonic amplitude, feed rate, and cutting speed on the machined surface morphology, roughness, surface residual stress, and subsurface microstructure in the longitudinal-torsional ultrasonic vibration-assisted end-milling process. According to the results, longitudinal-torsional ultrasonic vibration-assisted end milling can help form more obvious surface microtextures with a more distinct surface texture regularity at large amplitude, small feed rate, and high cutting speed. Compared with conventional milling, longitudinal-torsional ultrasonic vibration-assisted milling generates a larger roughness and surface residual stress and a deeper plastic deformation layer of the subsurface in the case of an obvious highly perturbed layer. In addition, the surface residual stress becomes greater and the plastic deformation layer gets deeper at a larger amplitude. When the amplitude was 5 μm, the surface residual stress was − 450.625 MPa and the depth of the deformation layer was 5.4 μm. The stress and depth increased by 21.55 % and 134.78 %, respectively, compared with those of conventional milling. The increase in the feed rate enhanced the roughness, decreased the surface residual stress, and did not significantly alter the depth of the plastic deformation layer. When the feed rate was 0.01 mm/z, the roughness was 0.383 μm and the surface residual stress was − 479.1 MPa. The feed rate and roughness increased by 42.63 % and 20.62 %, respectively, compared with those of conventional milling. With the increase in the cutting speed, the roughness increased, and the surface residual stress and the depth of the plastic deformation layer decreased. When the cutting speed was 15 m/min, the roughness was 0.31 μm, the surface residual stress value was − 454.7 MPa, and the depth of the plastic deformation layer was 5.7 μm. These three parameters increased by 17.8 %, 18.79 %, and 92.5 %, respectively, compared with those of conventional milling. This research has certain application prospect in surface machining of titanium alloy and quality control of machined surface.

Improvement in Surface Quality of Microchannel Structures Fabricated by Revolving Tip-Based Machining

Experimental study of a new micromilling process for vortex curved thin walls

Optimization of the process parameters for micro-milling thin-walled micro-parts using advanced algorithms

Analysis and optimization of microchannel array precision grinding processes with micro-structured micro-grinding tool

Mechanism of dual-direction vibration-assisted (DVA) micro-milling in surface formation considering the tool life-lengthening effect on the Ti6Al4V: design and experiment

Experimental Investigation on Machinability of Aluminum Alloy during Dry Micro Cutting Process Using Helical Micro End Mills with Micro Textures

Machining Slight Burr Formed Micro-Channels with Different Moving Trajectories of a Pyramidal Diamond Tip

Ultrasonic vibration assisted milling of titanium alloy microchannel

A Profile Shaping and Surface Finishing Process of Micro Electrochemical Machining for Microstructures on Microfluidic Chip Molds

Effect of process parameters on micro-textured surface generation in feed direction vibration assisted milling

Quality enhancement of micro-milled channels with automated laser assistance

Machinability improvement of titanium alloys in ultra-precision machining with micro-structured surface

Machining Surface Improvement through Electric- and Flow-Field Adjustments in Flying Electrochemical Milling of AA 2219

Surface and subsurface analysis of TC18 titanium alloy subject to longitudinal-torsional ultrasonic vibration-assisted end milling

Experimental Investigations on Surface Integrity in Thin Structure Machining of Aluminum 6061-T6

Surface quality evaluation of cold plasma and NMQL multi-field coupling eco-friendly micro-milling 7075-T6 aluminum alloy

Advances in micro milling: From tool fabrication to process outcomes

Evaluation of milling performance of 50-μm D-shaped carbide tool, polycrystalline diamond-coated carbide tool, and polycrystalline diamond tool

Surface feature and material removal in ultrasonic vibration-assisted slot-milling of Ti–6Al–4 V titanium alloy

Optimization of superalloy Inconel 718 micro-milling process by combined Taguchi and multi-criteria decision making method

Investigation of deviation and surface topography in ultrasonic vibration-assisted milling