Abstract:Cu2SnS3 (CTS), a typical ternary copper-based sulfide, is considered as a potential p-type thermoelectric (TE) material with the advantages of environmental friendliness and low cost, but its performance is limited by the high lattice thermal conductivity and electrical resistivity. Herein, we have successfully synthesized undoped and In-doped CTS nanoparticles with a pure tetragonal phase by the colloidal method. More interestingly, plenty of twin boundaries appear in all the samples sintered from the synthesized nanoparticles independent of composition. The twin boundaries can effectively reduce the lattice thermal conductivity, while the tetragonal phase is beneficial to meliorate the electrical performance of CTS. Consequently, the highest zT reaches 0.36 at 700 K for Cu2Sn0.85In0.15S3, which is enhanced by 17 times compared to that of the pristine CTS with mainly the monoclinic phase. The tunable phase and microstructure via the colloidal method provide useful guidance to promote the performance of eco-friendly TE sulfides.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c01483.Lattice thermal conductivity (κl) calculation; observed, calculated, and difference Rietveld refined XRD patterns for Cu2Sn1–xInxS3 (x = 0, 0.05, 0.1, 0.15, and 0.25) samples; SEM images under different magnifications of the Cu2Sn0.85In0.15S3-sintered sample; temperature dependence of electrical conductivity, Seebeck coefficient, PF of Cu2Sn0.85In0.15S3 ("brm" stands for before reversible measurement, "arm" stands for after reversible measurement); XRD patterns of Cu2Sn0.85In0.15S3; calculated band structures of In-doped t-CTS (Cu2Sn0.75In0.25S3); low-magnification TEM image, HRTEM image of Cu2SnS3; structural data (position, occupancies, Biso, and bond distances) of m-CTS, t-CTS, and c-CTS; and carrier concentration of Cu2Sn1–xInxS3 (x = 0, 0.05, 0.1, 0.15, and 0.25) samples (PDF)This article has not yet been cited by other publications.

CsCu5S3: Promising Thermoelectric Material with Enhanced Phase Transition Temperature.

High Thermoelectric Performance in Cu2SnS3 by Control Over Phase‐Dependent Mobility Edge

High Thermoelectric Figure of Merit Achieved in Cu2S1-xTex Alloys Synthesized by Mechanical Alloying and Spark Plasma Sintering

Are Cu2Te‐Based Compounds Excellent Thermoelectric Materials?

Β‐cscu5se3: A Promising Thermoelectric Material Going Beyond Photovoltaic Application

Multiple Phase Transitions and Structural Oscillations in Thermoelectric Cu2S at Elevating Temperatures

Phase Tuning for Enhancing the Thermoelectric Performance of Solution-Synthesized Cu 2– x S

Unlocking the Potential of Cu3SbSe3: Ultralow Thermal Conductivity and Enhanced Thermoelectric Performance

Phase Composition Manipulation and Twin Boundary Engineering Lead to Enhanced Thermoelectric Performance of Cu 2 SnS 3

Electronic Origin for the Enhanced Thermoelectric Efficiency of Cu2Se

Electronic origin of the enhanced thermoelectric efficiency of Cu2Se

Ultralow Glassy Thermal Conductivity and Controllable, Promising Thermoelectric Properties in Crystalline o-CsCu5S3

Phase Transition Behaviors and Thermoelectric Properties of CuAgTe 1– x Se x near 400 K

Is Cu₃SbSe₃ a Promising Thermoelectric Material?

Enhancing thermoelectric performance of Cu1.8S by Sb/Sn co-doping and incorporating multiscale defects to scatter heat-carrying phonons

Multiple Nanostructures in High Performance Cu2S0.5Te0.5 Thermoelectric Materials

Enhancing thermoelectric and mechanical properties of p-type Cu3SbSe4-based materials via embedding nanoscale Sb2Se3

Suppressed phase transition and enhanced thermoelectric performance in iodine-doped AgCuTe

High thermoelectric performance near the Mott–Ioffe–Regel limit in Cu S0.6Te0.4 meta-phases

Realizing the Ultralow Lattice Thermal Conductivity of Cu3SbSe4 Compound via Sulfur Alloying Effect

Approaching high thermoelectric performance in p-type Cu3SbS4-based materials by rational electronic and nano/microstructural engineering