Abstract:An ultra‐high figure of merit (ZT) is realized in MnTe via multiple valence bands convergence and localized lattice engineering by SbGeS alloying. The significant increase in ZT indicates MnTe as an emerging lead‐free thermoelectric material system for wide range of applications in waste heat recovery and power generation. MnTe has been considered a promising candidate for lead‐free mid‐temperature range thermoelectric clean energy conversions. However, the widespread use of this technology is constrained by the relatively low‐cost performance of materials. Developing environmentally friendly thermoelectrics with high performance and earth‐abundant elements is thus an urgent task. MnTe is a candidate, yet a peak ZT of 1.4 achieved so far is less satisfactory. Here, a remarkably high ZT of 1.6 at 873 K in MnTe system is realized by facilitating multiple valence band convergence and localized lattice engineering. It is demonstrated that SbGe incorporation promotes the convergence of multiple electronic valence bands in MnTe. Simultaneously, the carrier concentration can be optimized by SbGeS alloying, which significantly enhances the power factor. Simultaneously, MnS nanorods combined with dislocations and lattice distortions lead to strong phonon scattering, resulting in a markedly low lattice thermal conductivity(κlat) of 0.54 W m K−1, quite close to the amorphous limit. As a consequence, extraordinary thermoelectric performance is achieved by decoupling electron and phonon transport. The vast increase in ZT promotes MnTe as an emerging Pb‐free thermoelectric compound for a wide range of applications in waste heat recovery and power generation.

High thermoelectric performance near the Mott–Ioffe–Regel limit in Cu S0.6Te0.4 meta-phases

Multiple Nanostructures in High Performance Cu2S0.5Te0.5 Thermoelectric Materials

Are Cu2Te‐Based Compounds Excellent Thermoelectric Materials?

High Thermoelectric Performance in Cu2SnS3 by Control Over Phase‐Dependent Mobility Edge

Realizing High Thermoelectric Performance in Cu2Te Alloyed Cu1.15In2.29Te4

High thermoelectric properties of Cu2Te Ag2Te composite with Fe addition and non-stoichiometric Te

High Thermoelectric Figure of Merit Achieved in Cu2S1-xTex Alloys Synthesized by Mechanical Alloying and Spark Plasma Sintering

Lattice Distortions and Multiple Valence Band Convergence Contributing to High Thermoelectric Performance in MnTe.

Multiphase Coherent Nanointerface Network Enhances Thermoelectric Performance for Efficient Energy Conversion and Contactless Thermosensation Applications in GeTe

Interstitial Cu: An Effective Strategy for High Carrier Mobility and High Thermoelectric Performance in GeTe

Excellent thermoelectric properties and stability realized in copper sulfides based composites via complex nanostructuring

Enhanced thermoelectric properties of Mn Cu1.8S via tuning band structure and scattering multiscale phonons

Modulation doping promoted ultrahigh electron mobility and enhanced thermoelectric performance in PbTe

Synergistic modulation of mobility and thermal conductivity in (Bi,Sb)2Te3 towards high thermoelectric performance

Thermoelectric Performance Optimization and Phase Transition of GeTe by Alloying with Orthorhombic CuSbSe 2

Highly Enhanced Thermoelectric and Mechanical Properties of Bi-Sb-Te Compounds by Carrier Modulation and Microstructure Adjustment

Synergistic modulation of electrical and thermal transport toward promising n-type MgOCuSbSe2 thermoelectric performance by MO-intercalated CuSbSe2

Multiple Valence Bands Convergence and Localized Lattice Engineering Lead to Superhigh Thermoelectric Figure of Merit in MnTe

Achieving High Thermoelectric Performance in ZnSe-Doped CuGaTe2 by Optimizing the Carrier Concentration and Reducing Thermal Conductivity

Thermoelectric materials with crystal-amorphicity duality induced by large atomic size mismatch

High Thermoelectric Performance SnTe with a Segregated and Percolated Structure