Abstract:Modulation of the microstructure and configurational entropy tuning are the core stratagem for improving thermoelectric performance. However, the correlation of evolution among the preparation methods, chemical composition, structural defects, configurational entropy, and thermoelectric properties is still unclear. Herein, two series of AgSbTe2-based compounds were synthesized by an equilibrium melting-slow-cooling method and a nonequilibrium melting-quenching-spark plasma sintering (SPS) method, respectively. The equilibrium method results in coarse grains with a size of >300 μm in the samples and a lower defect concentration, leading to higher carrier mobility of 10.66 cm2 V-1 s-1 for (Ag2Te)0.41(Sb2Te3)0.59 compared to the sample synthesized by nonequilibrium preparation of 1.83 cm2 V-1 s-1. Moreover, tuning the chemical composition of nonstoichiometric AgSbTe2 effectively improves the configurational entropy and creates a large number of cation vacancies, which evolve into dense dislocations in the samples. Owing to all of these in conjunction with the strong inharmonic vibration of lattice, an ultralow thermal conductivity of 0.51 W m-1 K-1 at room temperature is achieved for the (Ag2Te)0.42(Sb2Te3)0.58 sample synthesized by the equilibrium preparation method. Due to the enhanced carrier mobility, optimized carrier concentration, and low thermal conductivity, the (Ag2Te)0.42(Sb2Te3)0.58 sample synthesized by the equilibrium preparation method possesses the highest ZT of 1.04 at 500 K, more than 60% higher than 0.64 at 500 K of the same composition synthesized by nonequilibrium preparation.

Porosity Induced Thermoelectric Performance Optimization for Antimony Telluride

Microstructure and thermoelectric properties of porous Bi 2 Te 2.85 Se 0.15 bulk materials fabricated by semisolid powder processing

Enhanced thermoelectric performance of n -type PbTe bulk materials fabricated by semisolid powder processing

Enhancing thermoelectric properties of p-type (Bi,Sb)2Te3 via porous structures

Porosity-mediated High-performance Thermoelectric Materials

Vacancy Manipulation by Ordered Mesoporous Induced Optimal Carrier Concentration and Low Lattice Thermal Conductivity in BixSb2- xTe3 Yielding Superior Thermoelectric Performance

Synergistic modulation of mobility and thermal conductivity in (Bi,Sb)2Te3 towards high thermoelectric performance

Enhanced Thermoelectric and Mechanical Performances in Sintered Bi0.48Sb1.52Te3-AgSbSe2 Composite.

Enhanced Thermoelectric and Mechanical Performances in Sintered Bi 0.48 Sb 1.52 Te 3 –AgSbSe 2 Composite

Enhancing Thermoelectric Performance of AgSbTe 2 -Based Compounds via Microstructure Modulation Combining with Entropy Engineering

Critical Role of Tellurium Self-Compensation in Enhancing the Thermoelectric Performance of P-Type Bi0.4Sb1.6Te3 Alloy

Electronic Topological Transition As a Route to Improve Thermoelectric Performance in Bi0.5 Sb1.5 Te3.

Designing Cost-Performance Porous Thermoelectric Materials by Interface Engineering Through Atomic Layer Deposition

Enhancing Thermoelectric Performance of SnTe Via Stepwisely Optimizing Electrical and Thermal Transport Properties

Effect of Porosity on Thermoelectric Performance of Hydrothermal Synthesized Bi2Te3

Optimized thermoelectric properties of AgSbTe 2 through adjustment of fabrication parameters

Synergistic Combination of Sb2Si2Te6 Additives for Enhanced Average ZT and Single-Leg Device Efficiency of Bi0.4Sb1.6Te3-based Composites

Enhanced Thermoelectric Performance in N-Type Bi2te2.95se0.05 Bulks Fabricated by High Pressure Sintering Technique

Optimization of the Thermopower of Antimony Telluride Thin Film by Introducing Tellurium Nanoparticles

Realizing high thermoelectric performance in Te nanocomposite through Sb2Te3 incorporation

Rare Earth Element Doping Introduces Pores to Improve Thermoelectric Properties of p-Type Bi 0.46 Sb 1.54 Te 3