Abstract:A novel direct coagulation casting via controlled release of high valence counter ions (DCC-HVCI) method was applied to prepare the alumina fiber-reinforced silica matrix composites with improved mechanical properties. In this method, the silica suspension could be rapidly coagulated via controlled release of calcium ions from calcium iodate and pH shift by hydrolysis of glycerol diacetate (GDA) at an elevated temperature. The influence of tetramethylammonium hydroxide (TMAOH) dispersant amount, volume fraction and calcium iodate concentration on the rheological properties of suspensions was investigated. Additionally, the effect of alumina fiber contents on the mechanical properties of alumina fiber-reinforced silica matrix composites was studied systematically. It was found that the stable suspension of 50vol% solid loading could be prepared by adding 2.5wt% TMAOH at room temperature. The addition of 0–15wt% alumina fibers had no obvious effect on the viscosity of the silica suspension. The controlled coagulation of the suspension could be achieved by adding 6.5gL−1 calcium iodate and 1.0wt% GDA after treating at 70°C for 30min. Compressive strength of green bodies with homogeneous microstructure was in the range of 2.1–3.1MPa. Due to the fiber pull-out and fracture behaviors, the mechanical properties of alumina fiber-reinforced composites improved remarkably. The flexural strength of the composite with 10wt% alumina fibers sintered at 1350°C was about 7 times of that without fibers. The results indicate that this approach could provide a promising route to prepare complex-shaped fiber-reinforced ceramic matrix composites with uniform microstructure and high mechanical properties.

Influence of fibers on the microstructure and compressive response of directional ice-templated alumina ceramics

Effect of Alumina Fiber Content on Pore Structure and Properties of Porous Ceramics

Fabrication of lamellar porous alumina with regular structure via directional solidification with multiple cold sources

Freeze-cast porous silica ceramics with alumina nanofibers addition

Effect of particle size on the lamellar pore microstructure of porous Al2O3 ceramics fabricated by the unidirectional freezing

Fabrication of Porous Alumina Ceramics with Directional Pore Channels Structure by Freeze-Gel Casting Processing

Control of Pore Structure During Freeze Casting of Porous SiC Ceramics by Different Freezing Modes

Alumina Aerogels with Unidirectional Channels under Different Freezing Temperatures During Freeze Casting—part I: Control and Analysis of Pore Channels

Ice-templated porous alumina structures

3D Long-Range Ordered Porous Ceramics Prepared by a Novel Bidirectional Freeze-Casting Technique

Alumina Fiber-Reinforced Silica Matrix Composites with Improved Mechanical Properties Prepared by a Novel DCC-HVCI Method

Formation Mechanism and Control of a Large-Scale Lamellar Structure in Freeze-Cast Al2O3 Ceramics under Dual Temperature Gradients

Lamellar and Interpenetrated Al/(Al2O3–TiC) Composites Prepared by Bidirectional Freeze Casting and Melt Infiltration

Preparation and Mechanical Property of Alumina Fibers Reinforced Thin Architectural Ceramic Plate

Al2O3 Ceramics with Well-Oriented and Hexagonally Ordered Pores: the Formation of Microstructures and the Control of Properties

Effects of Alcohol Additives on Pore Structure and Morphology of Freeze-Cast Ceramics

Creating Controllable Three-Dimensional Microstructures on the Surface of Carbon Fibers by Manipulating Ice Crystallization to Improve Interfacial Properties of Composites

Effects of Fiber Length and Solid Loading on the Properties of Lightweight Elastic Mullite Fibrous Ceramics

Lightweight alumina based fibrous ceramics with different high temperature binder

Porous mullite fiber-based ceramics inspired by biomimetic natural pine wood

Alumina Porous Ceramics Obtained by Freeze Casting: Structure and Mechanical Behaviour under Compression