Abstract:Mixed-potential type NH3 sensors were fabricated using La10Si5.5Al0.5O27 (LSAO) consisting of a porous layer and a dense layer as solid electrolyte and TiO2 as the sensing electrode. The effect of a LSAO porous layer and TiO2 phase transformation on sensor performances was investigated. The porous layer of LSAO electrolyte obviously enhanced sensor performance. Compared with the sensor without a LSAO porous layer, the sensor with LSAO porous layer exhibited larger responding potential values and higher sensitivity due to the enhanced three phase interface length. Anatase-TiO2 (a-TiO2) based sensor exhibited better sensing performance than rutile-TiO2 (r-TiO2) based sensor at the examined temperature range. A-TiO2 transformation toward r-TiO2 resulted in, poor sensing,performances of the sensor. The best sensing characteristics were achieved for the NH3 sensor with a-TiO2 sensing electrode calcined at 900 degrees C for 3 h. The potential values of the sensor response to NH3 linearly depended on the logarithm of NH3 concentrations at 450-600 degrees C and the sensitivity reached 169.7 mV/decade in the range of 50-400 ppm at 500 degrees C. At the same time, the sensor exhibited well anti-interference capability to H-2, NO, CH4 and CO2, but a little cross-sensitivity toward NO2 was observed. High temperature treatment (>900 degrees C) caused a-TiO2 transformation into r-TiO2 and V2O5 additions were conducive to TiO2 phase transformation. (C) 2016 Elsevier B.V. All rights reserved.

Improvement of Al 3+ ion conductivity by F doping of (Al 0.2 Zr 0.8 ) 4/3.8 NbP 3 O 12 solid electrolyte for mixed potential NH 3 sensors

Effect of LiF on the Ion Conductivity and Sinterability of (al0.2zr0.8)20/19nb(po4)3 Solid Electrolyte

A Mixed-Potential Type NH <sub>3</sub> Sensor Based on Spinel Zn <sub>2</sub>SnO <sub>4</sub> Sensing Electrode

A novel all-solid-state ammonium electrode with polyaniline and copolymer of aniline/2,5-dimethoxyaniline as transducers

Facile, Low‐Cost and Flexible Ammonia Sensor Arrays Based on Metallic Ion Charge Carriers and Polymer Matrices

A mixed-potential type NH3 sensors based on spinel Zn2SnO4 sensing electrode

Mixed potential NH<sub>3</sub> sensor based on Ag-Doped La<sub>2</sub>NiO<sub>4+</sub> sensing electrode

Mixed potential NH<sub>3</sub> sensor based on La<sub>9.95</sub>K<sub>0.05</sub>Si<sub>5</sub>Al<sub>1</sub>O<sub>26.45 </sub> electrolyte and Ag doped BiVO<sub>4</sub> sensing electrode

Mixed-potential Type NH3 Sensor Based on La10Si5.5Al0.5O27 Electrolyte and CuV2O6 Sensing Electrode

Al Doped into Si/P Sites of Na 3 Zr 2 Si 2 PO 12 with Conducted Na 3 PO 4 Impurities for Enhanced Ionic Conductivity

Amperometric Ammonia Sensors for Low Detection Limit with BaZr(1-x)YxO3-δ Proton Electrolytes

Improving the stability of an amperometric ammonia sensor based on BaZr0.8Y0.2O3-δ electrolyte with a volatile B2O3 sintering additive

An All-Solid-State Ammonium Ion-Selective Electrode Based on Polyaniline As Transducer and Poly (O-Phenylenediamine) As Sensitive Membrane

Enhancement of Ammonia Sensors Using In2O3 Sensing Electrode by Adjusting Particle Size and NiCo2O4 Reference Electrode

Mixed Potential Nh3 Sensor Based on Mg-Doped Lanthanum Silicate Oxyapatite

Synthesis and electrochemical properties of NASICON-type (Al0.2Zr0.8)(4-x)/3.8NbP3-xMoxO12 electrolytes

Mixed-potential type NH3 sensor based on TiO2 sensing electrode with a phase transformation effect

Enhanced Sensing Performance of Mixed Potential Ammonia Gas Sensor Based on Bi0.95Ni0.05VO3.975 by Silver

Study the Effect of Ion Doping on ZnO Nanostructures for Room Temperature NH3 Gas Sensor

A Highly Sensitive and Selective NH<sub>3</sub> Sensor Based on a Spherical In<sub>2</sub>O<sub>3</sub>-Sensing Electrode Prepared Using the Hydrothermal Method

Enhancing Ammonia Sensing Performance of Ag 2 MoO 4 -based Mixed-Potential Sensor by Introducing Ionic and Electronic Conductance