Abstract:The poly(vinylidene fluoride) (PVDF) as-spun fibers with different spin-stretching ratios were fabricated via melt-spinning method using plunger spinning machine. PVDF fibers with different post-stretching ratios were subsequently obtained by post-stretching method under the thermal treatment condition. The crystal and orientation structure of the fibers were investigated by X-ray diffraction (XRD), differential scanning calorimetry (DSC), polarizing optical microscopy (POM) and so on. The results indicated the orientation of alpha crystal and macromolecular increased with the increasing spin-stretching ratio. Furthermore, as the higher spinstretching ratio increased, the degree of crystallinity of as-spun fiber was prone to perfection. Furthermore, according to the POM photomicrograph, the horizon of extinction position was almost entirely black, and the horizon of diagonal position was getting brighter, due to the increase of the anisotropy of as-spun fibers. This was attributed that the irregular fiber macromolecules were stretched to regular structure. When spin-stretching ratio was 330, the crystallinity of as-spun fiber could reach 56.38% and the orientation factor of alpha(110/200) crystal plane was up to 0.89. In terms of post-stretching technique, the stretching ratios had no significant influence on the degree of crystallinity However, the post-stretching process played a positive role in the transition of the crystal phase from alpha to beta. The molecular chains of the fibers are easier to slip and arrange regularly along the fiber axis during spin-stretching process. The conformation was easier to transfer from alpha phase to beta phase owing to the segmental motion of molecular chains during post-stretching process. Especially, the orientation of beta crystal was also improved at the same time. Specially, when the post-stretching was up to the stage of uniform reduction of fiber diameter, the orientation of beta crystal retained a high level. When post-stretching ratio was 11, the content of beta crystal could account for 82.85% and the orientation factor of beta(110/200) crystal plane was up to 0.83.

Effect of Spin-Draw Rate and Stretching Ratio on Polypropylene Hollow Fiber Membrane Made by Melt-Spinning and Stretching Method

Structure formation and characterization of PVDF hollow fiber membranes by melt-spinning and stretching method

Preparation and Structural Control of Polyethylene Hollow Fiber Membranes

Effect of stretching on structure and properties of polyethylene hollow fiber membranes made by melt-spinning and stretching process

Effects of Cooling Ways on the Structure of Polypropylene Hollow Fiber Membranes Prepared by Stretching

Fabrication of Hydrophilic and Sponge-Like PVDF/brush-like Copolymer Blend Membranes Using Triethylphosphate As Solvent

Effect of Coagulation Bath Temperature on the Structure and Performance of Polyethersulfone Hollow Fiber Membranes by Dry/wet Process

Effects of stretching on crystalline phase structure and morphology of hard elastic PVDF fibers

Experimental And Numerical Analyses On The Poly(Lactide-Co-Glycolide) Hollow Fiber Membranes

Effect of Hot Stretching on the Structure of Polypropylene Microporous Membranes with in Situ Small Angle X-Ray Scattering

Effect Of Fiber Structure On The Properties Of The Electrospun Hybrid Membranes Composed Of Poly(E-Caprolactone) And Gelatin

Effect of Spinning Conditions on the Structure and Performance of Hydrophobic PVDF Hollow Fiber Membranes for Membrane Distillation

Influence of Dope Viscosity on the Fabrication of Pvdf Hollow Fiber Membranes with Single Skin Layer

Crystalline Structure Changes of Poly(vinylidene fluoride) Fibers during Stretching Process

The Effects of Spinning Temperature on Morphologies and Properties of Polyethersulfone Hollow Fiber Membranes

Effect of Viscosity and Air Gap within the Spinneret on the Morphology and Mechanical Properties of Hollow-Fiber Polymer Membranes for Separation Performance

A Study of Structure–Property Correlation on Wet Spinning Conditions in Heat-Resistant Poly(m-phenylene isophthalamide) Hollow Fiber Membranes

Effects of Room Temperature Stretching and Annealing on the Crystallization Behavior and Performance of Polyvinylidene Fluoride Hollow Fiber Membranes

Effect of Heat Treatment Mode and Aggressive Media on Mechanical Properties of Porous Polytetrafluoroethylene Membranes Fabricated via Electrospinning

Fabrication and Property Optimization of Electrostatic Spinning PVDF/PDMS Waterproof and Moisture Permeable Membrane

Preparation of poly(4-methyl-1-pentene) asymmetric or microporous hollow-fiber membranes by melt-spun and cold-stretch method