Abstract:Composites with a copper matrix attract the attention of researchers due to their ability to combine high ductility, heat conductivity, and electrical conductivity of the matrix with the high hardness and strength of the reinforcing phases. In this paper, we present the results of studying the effect of thermal deformation processing of a Сu-Ti-C-B composite produced by self-propagating high-temperature synthesis (SHS) on its ability to deform plastically without failure. The composite consists of a copper matrix and reinforced particles of titanium carbide TiC (sized up to 1.0 μm) and titanium diboride TiB2 (sized up to 3.0 μm). The composite hardness is 60 HRC. Under uniaxial compression, the composite starts to deform plastically at a temperature of 700 °C and a pressure of 100 MPa. Temperatures ranging between 765 and 800 °C and an initial pressure of 150 MPa prove to be the most effective condition for composite deformation. These conditions enabled a true strain of 0.36 to be obtained without composite failure. Under higher strain, surface cracks appeared on the specimen surface. The EBSD analysis shows that dynamic recrystallization prevails at a deformation temperature of at least 765 °C; therefore, the composite can plastically deform. To increase the deformability of the composite, it is proposed to perform deformation under conditions of a favorable stress state. Based on the results of numerical modeling by the finite element method, the critical diameter of the steel shell is determined, which is sufficient for deformation of the composite with the most uniform distribution of the stress coefficient k. Composite deformation in a steel shell under a pressure of 150 MPa, at 800 °C, is experimentally implemented until a true strain of 0.53 is reached.

Preparation and Anisotropic Compressive Deformation Behaviors of Tungsten Fiber Reinforced Cu-Zn Matrix Composite

Anisotropic compressive deformation behaviors of tungsten fiber reinforced Zr-based metallic glass composites

Insight into the Microstructure and Tensile Behavior of the W–Cu Composite Reinforced with Tungsten Fibers and Particulates

Anisotropic tensile properties of tungsten fiber reinforced Zr based metallic glass composites

Experimental Investigation of Tensile Properties and Fracture Mechanism of WCP/Cu Composites Reinforced with Different WCP Volume Fraction

Studying the Plastic Deformation of Cu-Ti-C-B Composites in a Favorable Stress State

Synthesis and Property of Short Tungsten Fibre/zr-Based Metallic Glass Composite

Freeze-casted tungsten skeleton reinforced copper matrix composites

Investigating the Effects of Contact Area and Chamfering on the Failure Behavior of Plain Woven Composite-Metal T-joints

Anisotropic microstructures and mechanical properties of textured Ti3AlC2/TiAl3/Al composite

Numerical investigations on the hybrid effect and deformation mechanism of TiB2p and TiBw reinforced Cu composites prepared by in-situ mixing casting

Research on dynamic mechanical behavior and damage evolution mechanism of Cu/WCp laminated composites

Deformation and fracture behavior of tungsten fiber-reinforced bulk metallic glass composite subjected to transverse loading

Improving comprehensive performance of copper matrix composite by spray pyrolysis fabricated CNT/W reinforcement

Preparation and mechanical properties of tungsten-particle-reinforced Zr-based bulk-metallic-glass composites

Interfacial Failure Mechanism in Tungsten Fiber Reinforced Copper-Based Composites Fabricated by Combustion Synthesis Melt Infiltration under Ultra-High Gravity

Mechanical and tribological properties of WC particles reinforced Cu-20Zn matrix composites

Microstructure and mechanical properties of tungsten fiber reinforced tungsten composites prepared by Fe activated sintering

Multilayered W-Cu composites with enhanced strength, electrical conductivity and wear resistance

Study on the Microstructure and Mechanical Properties of W-wire/TiBe, ZrBe, and ZrTiBe Alloy Composites

Mechanical Properties of a Novel Tungsten Fiber-Reinforced Tungsten Composite Prepared Through Powder Extrusion Printing and High-Pressure High-Temperature Sintering