Abstract:Water molecules lose electrons (which are oxidized) to form oxygen gas (O2), along with hydrogen ions (H+) and electrons. 2H2O→O2 +4H++4e−: Hydrogen ions (H+) gain electrons (which are reduced) to form hydrogen gas (H2). 4H++4e−→2H2: Together, these reactions split water into oxygen and hydrogen, with electrons transferred from the anode to the cathode. Hydrogen and renewable fuels were generated using cost‐effective and efficient electrocatalysts for water splitting. In this work, a CuO‐based photocathode is used for the water splitting to generate hydrogen energy by PVD technique. The XRD analysis reveals the deposition of CuO thin film on ITO substrates, which is monoclinic. The XRD and LSV analysis of CuO confirmed the type of semiconductor and observed to be P‐type semiconductor. SEM study of CuO confirmed the shape, morphology to be a circular and regular shape. The grain size of deposited CuO thin film was found to be 18 nm. The absorption and transmission of CuO thin film were observed through UV spectroscopy analysis and were found to be better photocatalyst in visible range 415–425 nm. The transmittance of the prepared thin film was noted to be maximum 7.6% in the UV range (280–300 nm). The band gap was also measured employing the Tauc plot and found to be 2.98 eV, which is most favorable for water splitting application. FTIR study showed the stretching, vibration, and the functional group of the deposited CuO thin film; the broad band of stretching of Cu‐O in monoclinic CuO was observed at the range of 500–700 cm−1, and further peaks were also noted at the range of 1500–1600 cm−1. The linear sweep voltammetry (LSV) of CuO thin film was calculated in the absence of solar spectra and the presence of solar spectra and observed to be enhanced in current under solar spectra. The solar light to hydrogen emission percentage (STH %) of CuO through LSV was observed to be 2.04% under solar spectra. The low Nyquist curve of blank ITO and CuO‐coated ITO substrate via electrochemical impedance spectroscopy (EIS) analysis was observed, which confirmed the enhancement of EIS of CuO‐coated ITO. The hydrogen generation rate was also calculated by electrochemical cell and observed to be 5325.21 mol g−1 for 6 h.

Effect of gold underlayer on copper(I) oxide photocathode performance

Exploring the Influence of Au Underlayer Thickness on Photocathode Performance

Enhancement of Solar-to-hydrogen Conversion Efficiency in Water Splitting by Optimizing Morphology of Cu2O Nanostructure and Surface Modification

Synthesis of a Cu2O/Carbon Film/NiCoB‐Grpahene Oxide Heterostructure As Photocathode for Photoelectrochemical Water Splitting

Cu ions intercalated GO/Cu 2 O photocathode-enabled promotion on charge separation and transfer for efficient photoelectrochemical water splitting

Cu2O/CuO heterojunction formed by thermal oxidation and decorated with Pt co-catalyst as an efficient photocathode for photoelectrochemical water splitting

Co-optimization of CuBi2O4 photocathode by heterojunction and hole-selective layer for efficient photoelectrochemical water splitting

Cu2O Photocathodes with Bidirectional CuSCN Layers to Improve Charge Separation for Enhanced Photoelectrochemical Water Splitting

Electrodeposition of Copper Oxides as Cost-Effective Heterojunction Photoelectrode Materials for Solar Water Splitting

Interfacial Study of Cu2o/Ga2o3/Azo/Tio2 Photocathode for Water Splitting Fabricated by Pulsed Laser Deposition

3D-printed Cu2O photoelectrodes for photoelectrochemical water splitting

Investigation of CuO/ITO Photoelectrode Fabricated by PVD for Efficient Photoelectrochemical Water Splitting and Hydrogen Evolution

Improvement of the Photoelectrochemical Stability of Cu2O Photocathode by PhCCCu Grafting

Cu2O Photocathodes for Unassisted Solar Water-Splitting Devices Enabled by Noble-Metal Cocatalysts Simultaneously As Hydrogen Evolution Catalysts and Protection Layers

Cu2O/CuO Bilayered Composite as a High-Efficiency Photocathode for Photoelectrochemical Hydrogen Evolution Reaction

Scalable Reduced Graphene Oxide Conductive Layer‐Based Particulate Photocathodes for Photoelectrochemical Water Splitting

Cu 2 O/CuO composite for efficient performance in photoelectrochemical and optoelectronics applications

Hollow cubic TiO2 loaded with copper and gold nanoparticles for photocatalytic CO2 reduction

Semitransparent Cu2O Films Based on CuO Back Layer for Photoelectrochemical Water Splitting and Photovoltaic Applications

3D Cathodes of Cupric Oxide Nanosheets Coated onto Macroporous Antimony-Doped Tin Oxide for Photoelectrochemical Water Splitting

Prominence of Copper in AuCu Alloy Towards Enhance Surface Plasmon Resonance-Driven Water Oxidation