Abstract:Water molecules lose electrons (which are oxidized) to form oxygen gas (O2), along with hydrogen ions (H+) and electrons. 2H2O→O2 +4H++4e−: Hydrogen ions (H+) gain electrons (which are reduced) to form hydrogen gas (H2). 4H++4e−→2H2: Together, these reactions split water into oxygen and hydrogen, with electrons transferred from the anode to the cathode. Hydrogen and renewable fuels were generated using cost‐effective and efficient electrocatalysts for water splitting. In this work, a CuO‐based photocathode is used for the water splitting to generate hydrogen energy by PVD technique. The XRD analysis reveals the deposition of CuO thin film on ITO substrates, which is monoclinic. The XRD and LSV analysis of CuO confirmed the type of semiconductor and observed to be P‐type semiconductor. SEM study of CuO confirmed the shape, morphology to be a circular and regular shape. The grain size of deposited CuO thin film was found to be 18 nm. The absorption and transmission of CuO thin film were observed through UV spectroscopy analysis and were found to be better photocatalyst in visible range 415–425 nm. The transmittance of the prepared thin film was noted to be maximum 7.6% in the UV range (280–300 nm). The band gap was also measured employing the Tauc plot and found to be 2.98 eV, which is most favorable for water splitting application. FTIR study showed the stretching, vibration, and the functional group of the deposited CuO thin film; the broad band of stretching of Cu‐O in monoclinic CuO was observed at the range of 500–700 cm−1, and further peaks were also noted at the range of 1500–1600 cm−1. The linear sweep voltammetry (LSV) of CuO thin film was calculated in the absence of solar spectra and the presence of solar spectra and observed to be enhanced in current under solar spectra. The solar light to hydrogen emission percentage (STH %) of CuO through LSV was observed to be 2.04% under solar spectra. The low Nyquist curve of blank ITO and CuO‐coated ITO substrate via electrochemical impedance spectroscopy (EIS) analysis was observed, which confirmed the enhancement of EIS of CuO‐coated ITO. The hydrogen generation rate was also calculated by electrochemical cell and observed to be 5325.21 mol g−1 for 6 h.

3D-printed Cu2O photoelectrodes for photoelectrochemical water splitting

Highly Efficient 2D/3D Structured CuCo2S4/CdIn2S4 Composites with a P–n Heterojunction for Boosting Photocatalytic Hydrogen Evolution

Synthesis of a Cu 2 O/Carbon Film/NiCoB‐Grpahene Oxide Heterostructure As Photocathode for Photoelectrochemical Water Splitting

Electrodeposition of Copper Oxides as Cost-Effective Heterojunction Photoelectrode Materials for Solar Water Splitting

Enhancement of Solar-to-hydrogen Conversion Efficiency in Water Splitting by Optimizing Morphology of Cu2O Nanostructure and Surface Modification

3D Porous Pyramid Heterostructure Array Realizing Efficient Photo‐Electrochemical Performance

3D Cathodes of Cupric Oxide Nanosheets Coated onto Macroporous Antimony-Doped Tin Oxide for Photoelectrochemical Water Splitting

Near-Ideal Copper Oxide Heterostructure Design for Photoelectrochemical Water Splitting

Highly efficient 3D/0D CdIn2S4/Cu2O photoanode with p-n type heterojunction for boosted photoelectrochemical water splitting under visible light irradiation

Investigation of CuO/ITO Photoelectrode Fabricated by PVD for Efficient Photoelectrochemical Water Splitting and Hydrogen Evolution

Scalable Reduced Graphene Oxide Conductive Layer‐Based Particulate Photocathodes for Photoelectrochemical Water Splitting

Cu2O/CuO heterojunction formed by thermal oxidation and decorated with Pt co-catalyst as an efficient photocathode for photoelectrochemical water splitting

Nanostructured 3-D nano-bricks shaped CuO – 0-D particle shaped Co 3 O 4 composite for superior photo-electrochemical water splitting

Photoelectrochemical performance of nanoscale Cu 2 O by integrating ZnO thin films mimicking a 3D–2D heterojunction: experiments & first-principles analysis

Three-Dimensional Decoupling Co-Catalyst from a Photoabsorbing Semiconductor as a New Strategy To Boost Photoelectrochemical Water Splitting

WO3@α‐Fe2O3 Heterojunction Arrays with Improved Photoelectrochemical Behavior for Neutral Ph Water Splitting

Design and In Situ Growth of Cu 2 O‐Blended Heterojunction Directed by Energy‐Band Engineering: Toward High Photoelectrochemical Performance

Cu ions intercalated GO/Cu 2 O photocathode-enabled promotion on charge separation and transfer for efficient photoelectrochemical water splitting

Integrated Hierarchical Cobalt Sulfide/Nickel Selenide Hybrid Nanosheets As an Efficient Three-dimensional Electrode for Electrochemical and Photoelectrochemical Water Splitting.

Fabrication of CuFe2O4/α-Fe2O3 Composite Thin Films on FTO Coated Glass and 3-D Nanospike Structures for Efficient Photoelectrochemical Water Splitting.

Co-optimization of CuBi2O4 photocathode by heterojunction and hole-selective layer for efficient photoelectrochemical water splitting