Abstract:The unique features of DLC coatings in providing low friction and low wear and, at the same time, causing low wear to the counterface make them very attractive in industrial applications, in improving tribological performance of mechanical components on various substrates. In this study, composite DLC coatings have been deposited on sintered ferrous alloy, M42 tool steel, 2618 aluminium alloy, and 6063 aluminium extrusion substrates using the combined CFUBMS-PACVD technique. The effect of mechanical properties of substrate materials on tribological behaviour of the composite DLC coatings has been investigated at various loads on a ball-on-disk wear machine in dry air. A transition load was usually observed for coatings on the various substrates except for the aluminium extrusion; above the transition load the coating was completely destroyed via some spallation/fragmentation process after 2 h sliding, and the wear rate increased dramatically with further increase in load. The coating system on sintered ferrous alloy substrate exhibited the highest transition load among the four types of substrates studied. This is considered to have resulted from the combined effects of the lower elastic modulus of the porous sintered ferrous alloy substrate, which decreases the stress concentrations in the contact region, and the surface roughness and porosity, which enhance the bonding strength between the coating and the substrate under multi-contact conditions. The high elastic modulus of the tool steel substrate leads to tensile stress conditions in the sliding contact region and therefore makes coatings deposited on such a substrate more prone to breakdown/fragmentation, resulting in a transition load close to that for coatings on the soft 2618 aluminium alloy substrate. For coatings on the 6063 aluminium extrusion substrate, significant plastic deformation occurred in the substrate at loads above 1.5 N. However, despite the heavy deformation in the substrate, coatings on this substrate were not scraped off, as were coatings on the 2618 aluminium alloy substrate, even at a load as high as 20 N. The specific wear rate increased continuously with load, no apparent transition load being explicitly identifiable. This study shows that hard DLC coatings can be applied on both hard and soft substrates for improvement of the tribological behaviour of mechanical components. (C) 1997 Elsevier Science Ltd.

Study on Failure Mechanisms of Dlc Coated Ti6al4v and Cocr under Cyclic High Combined Contact Stress

Substrate and bonding layer effects on performance of DLC and TiN biomedical coatings in Hank's solution under cyclic impact–sliding loads

Wear and corrosion properties of diamond like carbon (DLC) coating on stainless steel, CoCrMo and Ti6Al4V substrates

Study of the Fatigue Wear Behaviors of a Tungsten Carbide Diamond-Like Carbon Coating on 316L Stainless Steel

The Tribological Behaviors of Three Films Coated on Biomedical Titanium Alloy by Chemical Vapor Deposition

Tribological Performance of DLC Coating under Aqueous Solutions

Tribological study of lubricious DLC biocompatible coatings

The effect of diamond like carbon coating on the wear resistance at dry sliding conditions

Tribological Performance of Metal Doped Diamond-like Carbon Films Deposited on CoCrMo Alloy

Effect of aqueous solution and load on the formation of DLC transfer layer against Co-Cr-Mo for joint prosthesis.

The effect of substrate properties on tribological behaviour of composite DLC coatings

Friction and wear study of diamond-like carbon gradient coatings on Ti6Al4V substrate prepared by plasma source ion implant-ion beam enhanced deposition

Nano-scratch and Fretting Wear Study of DLC Coatings for Biomedical Application

Effect of carburizing treatment on microstructural, mechanical and tribological performances of Cr doped DLC coating deposited on Ti6Al4V alloy

Study on the substrate surface micro-texturing/carburizing regulating the film-substrate adhesion and wear behavior of DLC coatings

Tribological behavior of different films on Ti-6Al-4V alloy prepared by plasma-based ion implantation

Performance of CoCrMo Alloy with Me-Doped DLC Coatings Prepared by a Magnetron Sputtering Method

Tribocorrosion Behavior of Dlc-Coated Cocrmo Alloy in Simulated Biological Environment

DLC coating over pre-oxidized and textured Ti6Al4V for superior adhesion and tribo-performance of hip implant

The Appraisal of Biotribological Properties of DLC Gradient Film on Titanium Alloy Substrate

Mechanical and Unlubricated Tribological Properties of Titanium-Containing Diamond-Like Carbon Coatings