Abstract:The unique features of DLC coatings in providing low friction and low wear and, at the same time, causing low wear to the counterface make them very attractive in industrial applications, in improving tribological performance of mechanical components on various substrates. In this study, composite DLC coatings have been deposited on sintered ferrous alloy, M42 tool steel, 2618 aluminium alloy, and 6063 aluminium extrusion substrates using the combined CFUBMS-PACVD technique. The effect of mechanical properties of substrate materials on tribological behaviour of the composite DLC coatings has been investigated at various loads on a ball-on-disk wear machine in dry air. A transition load was usually observed for coatings on the various substrates except for the aluminium extrusion; above the transition load the coating was completely destroyed via some spallation/fragmentation process after 2 h sliding, and the wear rate increased dramatically with further increase in load. The coating system on sintered ferrous alloy substrate exhibited the highest transition load among the four types of substrates studied. This is considered to have resulted from the combined effects of the lower elastic modulus of the porous sintered ferrous alloy substrate, which decreases the stress concentrations in the contact region, and the surface roughness and porosity, which enhance the bonding strength between the coating and the substrate under multi-contact conditions. The high elastic modulus of the tool steel substrate leads to tensile stress conditions in the sliding contact region and therefore makes coatings deposited on such a substrate more prone to breakdown/fragmentation, resulting in a transition load close to that for coatings on the soft 2618 aluminium alloy substrate. For coatings on the 6063 aluminium extrusion substrate, significant plastic deformation occurred in the substrate at loads above 1.5 N. However, despite the heavy deformation in the substrate, coatings on this substrate were not scraped off, as were coatings on the 2618 aluminium alloy substrate, even at a load as high as 20 N. The specific wear rate increased continuously with load, no apparent transition load being explicitly identifiable. This study shows that hard DLC coatings can be applied on both hard and soft substrates for improvement of the tribological behaviour of mechanical components. (C) 1997 Elsevier Science Ltd.

Tribocorrosion Behavior of Dlc-Coated Cocrmo Alloy in Simulated Biological Environment

Tribological Properties of Diamond-Like Carbon Films Deposited by Vacuum Arc

Effect of aqueous solution and load on the formation of DLC transfer layer against Co-Cr-Mo for joint prosthesis.

Wear and corrosion properties of diamond like carbon (DLC) coating on stainless steel, CoCrMo and Ti6Al4V substrates

Improving biotribological properties and corrosion resistance of CoCrMo alloy via a Cr-GLC nanocomposite film in simulated body fluids

Tribological Performance of DLC Coating under Aqueous Solutions

Friction and Wear of Diamond-Like Carbon Film Deposited on Cocrmo Alloy under Different Lubrication

Tribological study of lubricious DLC biocompatible coatings

Investigating the Roles of Protein on the Cobalt Alloy Surface Degradation for Biomedical Implant Through Tribocorrosion Mechanisms

Feasibility of using diamond-like carbon films in total joint replacements: a review

Study on Failure Mechanisms of Dlc Coated Ti6al4v and Cocr under Cyclic High Combined Contact Stress

Tribological Performance and Anticorrosion Stability of Co-Cr-Mo Alloy with Thermal Oxidation Layer under Bovine Serum Albumin Solution

Tribological Performance of Metal Doped Diamond-like Carbon Films Deposited on CoCrMo Alloy

Performance of CoCrMo Alloy with Me-Doped DLC Coatings Prepared by a Magnetron Sputtering Method

Diamond-like Carbon Film and Its Application on Articular Surface of Artificial Joint for Increasing Wear Resistance

Tribological Behavior of Diamond Like Carbon Film Sliding Against Cocrmo or Al2o3 in Air and Water Environment

Tribo-mechanism of Amorphous Carbon Films under Corrosion Solution and Various Mechanical Loads

Comprehensive structural, nanomechanical and tribological evaluation of silver doped DLC thin film coating with chromium interlayer (Ag-DLC/Cr) for biomedical application

The effect of substrate properties on tribological behaviour of composite DLC coatings

Tribocorrosion Susceptibility and Cell Viability Study of 316L Stainless Steel and Ti6Al4V Titanium Alloy with and without DLC Coatings

High Temperature Passive Film on the Surface of Co–Cr–Mo Alloy and Its Tribological Properties