Abstract:This study investigates the potential use of Yellow River sand (YRS) sourced from the lower reaches of the Yellow River in China as a sustainable and cost-effective substitute for quartz sand in Engineered Cementitious Composites (ECC). With an annual accumulation of approximately 400 million tons in this region, YRS presents a substantial resource. ECC specimens with 100% YRS replacement with quartz sand were subjected to various curing methods: natural, steam, standard, and sprinkler. Extensive mechanical testing including flexural, compressive, uniaxial tensile, and four-point flexural tests was conducted. Additionally, Scanning Electron Microscope (SEM) and Mercury Intrusion Porosimetry (MIP) analyses investigated microscopic mechanisms influencing macroscopic mechanical properties. Finally, the mechanical properties of the YRS-ECC test block after 14 days of standard curing and the traditional sand ECC test block were compared and analyzed. The results indicate that ECC specimens with 100% YRS substitution under natural curing show an optimal ultimate tensile strain of more than 4%, providing the best resistance to the reduction in ultimate flexural load and deflection due to aging. Steam curing enhances flexural and compressive strength, achieving an ultimate flexural load of 5 kN and a maximum deflection of 4.42 mm at 90 days. SEM analysis revealed lower C-S-H gel density under natural curing and higher under steam curing, enhancing fiber pull-out in steam-cured specimens. The MIP tests demonstrated that natural curing had the highest porosity (32.86%) and average pore size (51.69 nm), whereas steam curing resulted in the smallest average pore size, with 44% of pores under 50 nm. Compared with traditional sand, it is found that the ultimate bending load and deflection of YRS-ECC are 5.7% and 9.4% higher than those of traditional sand ECC, respectively, and its ultimate tensile strength and strain are also improved. These findings highlight YRS as a sustainable alternative to natural sand in ECC, with natural curing proving the most effective for superior mechanical performance, including tensile strain, crack resistance, and durability.

Effect of Water-Curing Time on the Mechanical Properties of Engineered Cementitious Composites

Mechanical Properties and Carbonation Durability of Engineered Cementitious Composites Reinforced by Polypropylene and Hydrophilic Polyvinyl Alcohol Fibers

Experimental Study on Engineering Properties of Cemented Soil with High Water Content

Effect of Curing Conditions on Property of High Performance Concrete with Composite Mineral Admixture

The Influence of Fly Ash on the Bending Characteristics of Cost-Effective Cementitious Composites

Investigation of the Mechanical Properties of Engineered Cementitious Composites with Low Fiber Content and with Crumb Rubber and High Fly Ash Content

Engineered cementitious composites using blended limestone calcined clay and fly ash: Mechanical properties and drying shrinkage modeling

An Overview on the Influence of Various Parameters on the Fabrication and Engineering Properties of CO2-cured Cement-Based Composites

Durability Performances of Carbon Fiber-Reinforced Polymer and Concrete-Bonded Systems under Moisture Conditions

Mechanical Performance of Low Shrinkage Engineered Cementitious Composite in Tension and Compression

Influence of free water on compressive fatigue properties of ECC

Effect of Fiber Type and Volume Fraction on Fiber Reinforced Concrete and Engineered Cementitious Composite Mechanical Properties

Study on the Durability of Engineered Cementitious Composites (eccs) Containing High-Volume Fly Ash and Bentonite Against the Combined Attack of Sulfate and Freezing-Thawing (F-T)

Use of Slag to Improve Mechanical Properties of Engineered Cementitious Composites (eccs) with High Volumes of Fly Ash

The Influence and Mechanism of Curing Methods and Curing Age on the Mechanical Properties of Yellow River Sand Engineered Cementitious Composites

Design and Performance of Cost-Effective Green Engineered Cementitious Composites with Low Drying Shrinkage and Self-Healing

Study on the Effect of Curing Condition on the Performance of Fbc Ash

Effects of different curing regimes on the compressive strength properties of self compacting concrete incorporating fly ash and silica fume

Influence of Zeolite Addition on Mechanical Performance and Shrinkage of High Strength Engineered Cementitious Composites

A Comparative Study on the Mechanical Properties and Microstructure of Cement-Based Materials by Direct Electric Curing and Steam Curing

Durability Performance Investigation for Engineering Fiber Cementitious Composites (ECC): Review