Abstract:Injection molding is widely used for the mass production of plastic components. However, an appropriate choice of the process parameters is essential to ensure the precision and uniformity of the molded parts. The flow length-to-wall thickness (L/t) ratio for most molded components lies in the range of 100∼200. For higher values of the L/t ratio, the flow resistance increases dramatically at the end of the molded part and the injection pressure propagates less easily through the mold cavity. Consequently, the geometric dimensions of the molded parts in the near-gate region are frequently different from those in the far-from-gate region as well as resulting in lower uniformity. In practice, the variation in the geometric dimensions is significantly dependent on the filling-to-holding (V/P) switchover point, injection speed, and holding condition. Accordingly, the present study commences by proposing a simple least-squares regression-based approach for determining the appropriate V/P switchover point based on the quality requirement for the geometric dimensions of the molded component. In addition, a multi-stage holding condition is used to improve the geometric uniformity of the molded component by minimizing the residual pressure difference between the near-gate and far-from-gate regions of the mold at the end of the packing stage. Finally, a deceleration strategy is considered for the injection screw at the end of the filling stage to further reduce the quality variation. The experimental results show that for molded components with a large L/t ratio, the V/P switchover point should be determined based on the quality requirement for the part in the far-from-gate region in order to avoid insufficient quality compensation in the early holding stage. Furthermore, compared with the single-stage holding condition, the multi-stage holding condition reduces the residual pressure difference between the near-gate and far-from-gate regions of the cavity by around 74.5% (from 48.7 to 12.5 MPa). As a result, the difference in width between the near-gate region of the molded component and the far-from-gate region is reduced by about 66.7% (0.09 to 0.03 mm), while the difference in thickness is reduced by approximately 32.1% (0.028 to 0.019 mm). The deceleration strategy for the injection screw has no noticeable effect on the quality uniformity of the molded part provided that the V/P switchover point and multi-stage holding pressure are appropriately designed.

Study on the Effect of Gate Size on Properties of Dynamic Injection Molding Samples

Effect on Residual Wall Thickness of Parts with Floating Core Injection of Water-Assisted Injection Molding

Study on Processing Parameters of Ceramic Injection Moulding

A novel and simple method to improve thermal imbalance and sink mark of gate region in injection molding

Research on Quality Characterization Method of Micro-Injection Products Based on Cavity Pressure

Study of the Effect of Processing Conditions on Deflection of Injection Products

Determination of casting parameters of thick wall die-casting of magnesium alloy and simulation of its processing

Determination of process parameters based on cavity pressure characteristics to enhance quality uniformity in injection molding

Visual Computer-based Simulation of Sandwich Injection Molding Process:Influence of Shape of Rectangle Goods and Injection Gate Location on Breakthrough Phenomenon of Core Melt

Effect of Micro-Mold Cavity Dimension on Structure Andproperty of Polylactic Acid/Polycaprolactone Blend Undermicroinjection Molding Conditions

The Study of the effect of material mixing on pin injection screw

Effect of Micro-Mold Cavity Dimension on Structure and Property of Polylactic Acid/Polycaprolactone Blend under Microinjection Molding Conditions

Enhancing the quality stability of injection molded parts by adjusting V/P switchover point and holding pressure

Experiment and Simulation of Foaming Injection Molding of Polypropylene/nano-Calcium Carbonate Composites by Supercritical Carbon Dioxide

Effect of gas on the polymer temperature in external gas-assisted injection molding

Study on Computer Simulation of Co-injection Molding

Flow Simulation and Defects Analysis of Injection Molded Parts Based on CAE Technique

Study on the Influence of Injection Velocity on the Evolution of Hole Defects in Die-Cast Aluminum Alloy

Effect of rapid heating cycle injection mold temperature on crystal structures, morphology of polypropylene and surface quality of plastic parts

Effects of the Super Slow Speed Die Casting Process Parameters on Properties of ADC12 Aluminum Alloy

Analysis of the Effects on the Quality of Micro Injection Molded Products