Abstract:Towards the low-cost fabrication of a hard imprinting mold with micro-and nanostructures,a novel photocurable inorganic polymer was modified from perhydropolysilazane(PHPS) by grafting with 2-isocyanatoethyl methacrylate(ICMA) in this paper.The as-modified product was characterized by the methods of FTIR,1H-NMR,13C-NMR and 2D-1H-1H-NMR(COSY).The new peaks at δ=3.2~3.8 on1H-NMR spectra of the product were assigned to be the NH—CH2 group,and δ=152~158 on 13C-NMR spectra was assigned to be the CO—NH group.In the FTIR spectra,the absorbing peaks at 2153 and 1363 cm-1(N-C-O),1117 cm-1(—C—N-C) of PHPS were obviously consumed after chemical modification,and the new peaks at 1690,1530 and 1314 cm-1(CO—NH)were appeared.Combined with the COSY analysis,it was concluded that the UV sensitive methacrylyate group was successfully grafted to PHPS,and methacrylated perhydropolysilazane(MPHPS) was used to name the as-modified product here.MPHPS was then used to fabricate the micro-and nanostructures via UV imprinting lithography using a fluoropolymer(FP) mold with microstructures,adding a pressure ranged in 0.1~0.4 MPa.The efficiency of the pattern transfer from FP mold was increased by the pressure increasing,and the thoroughly pattern copy was realized at 0.23 MPa.Besides,nanostructures with 90 nm,70 nm feature sizes were obtained at the pressure of 0.4 MPa.Then the as-prepared micro-and nanostructures were converted into Si—O inorganic phase by a followed hydrolysis treatment.The converted product was concluded to be a composition of SiO1.5 from XPS depth profile.The final obtained mold was optical transparent,and with a hardness of 4.5×103 MPa and a elastic modulus of 115×103 MPa.

Study on the Mold Fabrication Process for Imprint Lithography

A Method for Improving the Precision of Soft-Mold Manufacturing for Imprint Lithography

Process Parameters of Mold Fabrication for Nano-Imprint Lithography

Template Fabrication Process in Step and Flash Imprint Lithography

Fabrication of Flexible Mold for Hybrid Nanoimprint-Soft Lithography

Process Control for Nanoimprint Lithography

Development of a Step Micro-Imprint Lithography Tool

Research on the Cast Molding Process for High Quality PDMS Molds

Template Fabrication on Soft Ultravialet Nanoimprint Lithography

Fluorosilicone as an Omnimold for Microreplication

HIGH RESOLUTION SILICA IMPRINTING MOLD FABRICATED FROM A PHOTOCURABLE PERHYDROPOLYSILAZANE

Using Silicon Molds for Ultrasonic Embossing on Polymethyl Methacrylate (PMMA) Substrates

A novel method for fabricating polydimethylsiloxane microfluidic chip master molds

Mold Deformation in Soft UV-nanoimprint Lithography

Large Area Mold Fabrication for the Nanoimprint Lithography Using Electron Beam Lithography

Making Modified Fluoropolymer Molds for Ultraviolet Nanoimprint Lithography

Room-Temperature Capillary-Imprint Lithography for Making Micro-/Nanostructures in Large Areas

Scanning probe lithography for nanoimprinting mould fabrication

High fidelity 3D thermal nanoimprint with UV curable polydimethyl siloxane stamps

Evaluation of micro-replication technology using silicone rubber molds and its applications

Effects of Exposure Time on Defects and Demolding Force in Soft Ultraviolet Nanoimprint Lithography