Abstract:Journal of Biomaterials Applications, Ahead of Print. Fabricating scaffolds using three-dimensional (3D) printing is an emerging approach in tissue engineering (TE), where filaments with a controlled arrangement are printed. Using fused deposition modeling in bone replacement enables the simulation of bone structure. However, the microenvironment created by the scaffold must meet specific requirements. These requirements aim to create an environment that promotes adhesion, proliferation, differentiation, and cell migration. One of the challenges in creating polylactic acid scaffolds is controlling the degradation rate to match the target tissue. This study investigates the degradation of scaffolds with different geometries and the relationship between scaffolds' geometry and degradation rate. These scaffolds are made of polylactic acid and prepared using 3D printing. The lattice geometry was exposed to acidic media with varying pH levels for 1 month, and pH2 was selected for all geometries for further investigation. The five selected geometries were then immersed in the desired acid for 2 months, and measurements were taken for wet weight, dry weight, morphology, molecular weight, and crystallinity during degradation. The results showed that the hexagonal sample had a 1.5% increase in wet weight, and the gyroid sample had a 1.2% increase, indicating that the wavy shapes had a higher fluid-holding capacity. The degradation analysis indicated that the hexagonal geometry had accelerated degradation compared to the other geometries. Based on these findings, it can be concluded that filament separation not only results in rapid cooling and prevents the recovery of the crystalline arrangement but also increases the surface area to volume ratio, allowing for more acid penetration and faster degradation. Finally, mechanical properties and in vitro evaluation were assessed for three selected geometries. On the 60th day, the hexagonal scaffold had the highest elastic modulus value of 105 ± 0.45 MPa, while the gyroid scaffold had the lowest value of 58.8 ± 0.40 MPa. The lattice scaffold had the highest amount of cell attachment, with 210.88 ± 0.35 cells surviving after 24 hours and 94.01 ± 0.18 cells surviving after 72 hours. These high viability rates indicate that the three scaffolds with the selected geometries are suitable for promoting cell growth.

Influence of Poly(lactic Acid)scaffold Structure to Its Degradability in SBF

Effects of Porosity and Pore Size on in Vitro Degradation of Three-Dimensional Porous Poly(d,l-Lactide-co-glycolide) Scaffolds for Tissue Engineering.

Effects Of Scaffold Design Parameters And Local Environment On Biopolymer Scaffold Degradation

Influence of scaffold geometry on the degradation rate of 3D printed polylactic acid bone scaffold

DEGRADATION STUDY OF POLY(LACTIC ACID) POROUS SCAFFOLD AT DIFFERENT TEMPERATURES

The Biodegradability of Electrospun Dextran/PLGA Scaffold in a Fibroblast/macrophage Co-Culture

Biosoluble ceramic fiber reinforced poly(L-lactic acid) bone scaffold: degradation and bioactivity

Effect of Porosity on Long-Term Degradation of Poly (Ε-Caprolactone) Scaffolds and Their Cellular Response

In vitro degradation of fibrous bilayer poly-L-lactic acid scaffolds

Effect of Bore Fluid Composition on Poly(lactic-Co-glycolic Acid) Hollow Fiber Membranes Fabricated by Dry-Jet Wet Spinning

Accelerated degradation of poly(l-lactide) bone scaffold: Crystallinity and hydrophilicity

Degradation behavior of 2D auxetic structure with biodegradable polymer under mechanical stress

Mechanical deviation in 3D-Printed PLA bone scaffolds during biodegradation

Physical and degradation properties of PLGA scaffolds fabricated by salt fusion technique

In vitro and in vivo degradability and cytocompatibility of poly(l-lactic acid) scaffold fabricated by a gelatin particle leaching method.

In situ comparison of osteogenic effects of polymer-based scaffolds with different degradability by integrated scaffold model

Degradation mechanisms and acceleration strategies of poly (lactic acid) scaffold for bone regeneration

In Vitro and in Vivo Degradability and Cytocompatibility of Poly(l-Lactic Acid) Scaffold Fabricated by a Gelatin Particle Leaching Method

Effect of degradation in polymer scaffolds on mechanical properties: Surface vs. bulk erosion

Effects of Degradation Media of Polyester Porous Scaffolds on Viability and Osteogenic Differentiation of Mesenchymal Stem Cells

Preparation and in Vitro Degradation Behavior of Biodegradable Porous Zn-Li-Ca Alloy Bone Repair Scaffolds