Abstract:The addition of inorganic fillers has been deemed as an effective strategy for reducing the mold shrinkage of polypropylene (PP). However, the current understanding on the underlying mechanisms is still unclear. In this work, taking talc filled isotactic PP (i-PP) i-PP) as an example, the effect and mechanisms of inorganic particles on the linear shrinkage of injection-molded i-PP products were investigated theoretically and experimentally. The results indicate that, at low contents (<6 vol%) of talc, the linear shrinkage of the injection-molded products in both in-plane ( i.e. , along the machine direction MD and transverse direction TD) and out-of-plane directions (i. i. e. , along the thickness direction ND) is found to decrease linearly with increasing talc content, which is consistent with the theoretical prediction. However, at high contents (>6 vol%) of talc, the change trend of the linear shrinkage deviates significantly from the theoretical curves. The in-plane shrinkage decreases remarkably, while the out-of-plane shrinkage remains almost unchanged. Further analysis indicates that the talc plates in the injection- molded products show a strong tendency to align along the MD-TD plane and induce the growth of i-PP lamellae perpendicular to their surfaces. Accordingly, the dense talc network promotes the formation of highly oriented i-PP lamellae perpendicular to the MD-TD plane, ultimately leading to a much lower in-plane linear shrinkage but a higher out-of-plane shrinkage as compared to the theoretical values. Achieving low in-plane linear shrinkage is particularly beneficial for the development of large-sized thin-walled products. Our work not only breaks through the current knowledge (the shrinkage of composites is decreased based on the increased volume fraction of fillers) and gives a new insight on the role of the filler-induced orientation crystallization in tailoring the shrinkage of PP products, but also provides a solution for the development of low-shrinkage PP materials.

THE QUANTITATIVE DESCRIPTION OF AGGREGATION STRUCTURE AND THE RELATIONSHIP WITH MECHANICAL PROPERTIES OF PP MATERIAL

The Research on Aggregation Structure of PP Materials under Different Condition and the Influence on Mechanical Properties

ADVANCE IN EFFECT OF AGGREGATION STRUCTURE OF PP ON MECHANICAL PROPERTIES

The Effects of the Aggregation Structure Parameters on Impact-Fractured Surface Fractal Dimension and Strain-Energy Release Rate for Polypropylene

Characterization of Microstructure of Polypropylene Alloys

Additive Effects of N,N,N′,N′ -Tetraalkyl Terephthalamide on Crystalline Morphology and Mechanical Properties of Polypropylene

AN ATOMIC FORCE MICROSCOPY STUDY ON THE AGGREGATION OF ISOTACTIC POLY(METHYL METHACRYLATE)

The Effect of Nucleating Agent on the Crystalline Morphology of Polypropylene (Pp)

Study on Structure and Property Relations of Α‐ipp During Uniaxial Deformation Via in Situ Synchrotron SAXS/WAXS and POM Investigations

Relative Molecular Weight and Distribution, Crystallization Behavior and Mechanical Properties of PP Powders with Different Particle Sizes

The Effect of Talc and It's Filling Method on Crystalline Morphology of PP Material

EFFECTS OF NUCLEATING AGENT ON CRYSTALLINE MORPHOLOGY AND IMPACT BEHAVIOUR OF POLYPROPYLENE

Study on the Mechanism of the Flake-shaped Filler Tailored Linear Shrinkage of Polypropylene

Relationship between molecular structure, crystallization behavior, and mechanical properties of long chain branching polypropylene

Effects of Stereo-Defect Distribution on the Crystalline Morphology and Tensile Behavior of Isotactic Polypropylene Prepared by Compression Molding Process

Effect of Different Nucleating Agent on Crystal Morphology and Properties of PP

Crystalline Morphology of PP Filled with Nucleating Agent

MICRO-STRUCTURE AND MECHANICAL PROPERTIES OF IN-SITU POLYMERIZATION-MODIFIED TALC/PP COMPOSITES

Crystallization Behavior and Morphological Development of Isotactic Polypropylene with an Aryl Amide Derivative As Β-Form Nucleating Agent Part B Polymer Physics

Effects Of Melt Structure On Crystallization Behavior Of Isotactic Polypropylene Nucleated With Alpha/Beta Compounded Nucleating Agents

Studies on crystal morphology and crystallization kinetics of polypropylene filled with CaCO3 of different size and size distribution