Abstract:The addition of inorganic fillers has been deemed as an effective strategy for reducing the mold shrinkage of polypropylene (PP). However, the current understanding on the underlying mechanisms is still unclear. In this work, taking talc filled isotactic PP (i-PP) i-PP) as an example, the effect and mechanisms of inorganic particles on the linear shrinkage of injection-molded i-PP products were investigated theoretically and experimentally. The results indicate that, at low contents (<6 vol%) of talc, the linear shrinkage of the injection-molded products in both in-plane ( i.e. , along the machine direction MD and transverse direction TD) and out-of-plane directions (i. i. e. , along the thickness direction ND) is found to decrease linearly with increasing talc content, which is consistent with the theoretical prediction. However, at high contents (>6 vol%) of talc, the change trend of the linear shrinkage deviates significantly from the theoretical curves. The in-plane shrinkage decreases remarkably, while the out-of-plane shrinkage remains almost unchanged. Further analysis indicates that the talc plates in the injection- molded products show a strong tendency to align along the MD-TD plane and induce the growth of i-PP lamellae perpendicular to their surfaces. Accordingly, the dense talc network promotes the formation of highly oriented i-PP lamellae perpendicular to the MD-TD plane, ultimately leading to a much lower in-plane linear shrinkage but a higher out-of-plane shrinkage as compared to the theoretical values. Achieving low in-plane linear shrinkage is particularly beneficial for the development of large-sized thin-walled products. Our work not only breaks through the current knowledge (the shrinkage of composites is decreased based on the increased volume fraction of fillers) and gives a new insight on the role of the filler-induced orientation crystallization in tailoring the shrinkage of PP products, but also provides a solution for the development of low-shrinkage PP materials.

The Effect of Talc and It's Filling Method on Crystalline Morphology of PP Material

Effect of Different Nucleating Agent on Crystal Morphology and Properties of PP

The Research on Aggregation Structure of PP Materials under Different Condition and the Influence on Mechanical Properties

Effect of Inorganic Filler on the Crystallization, Mechanical Properties and Rheological Behavior of Poly(Trimethylene Terephthalate)

Additive Effects of N,N,N′,N′ -Tetraalkyl Terephthalamide on Crystalline Morphology and Mechanical Properties of Polypropylene

Effects of Inorganic Fillers on the Thermal and Mechanical Properties of Poly(lactic acid).

Studies on crystal morphology and crystallization kinetics of polypropylene filled with CaCO3 of different size and size distribution

The effect of talc orientation and transcrystallization on mechanical properties and thermal stability of the polypropylene/talc composites

The Effect of Talc on the Mechanical, Crystallization and Foaming Properties of Poly(Lactic Acid)

Mechanical and Thermal Properties of Polypropylene (PP) Composites Filled with CaCO3 and Shell Waste Derived Bio-Fillers

Effect of Morphology of Polyimide/Talc Composite Film on Its Properties

Effect of the Crystalline Morphology on Pore Generation of β-PP Under Uniaxial Tension

The Influence of Melt Temperature on the Crystal Orientation of Polypropylene Containing Talc

Influence of N,N,N′,N′-tetraalkyl terephthalamide on isothermal crystallization kinetics and morphology evolution of polypropylene

Study on the Mechanism of the Flake-shaped Filler Tailored Linear Shrinkage of Polypropylene

Effects Of Talcum Powder(Talc) And Compounding Sequence On The Morphology And Mechanical Properties Of Pa6/Pp/Mapp Blend

Crystalline Morphology of PP Filled with Nucleating Agent

Preparation and characterization of poly(L-lactide)-co-poly(trimethylene carbonate)/talc film

THE QUANTITATIVE DESCRIPTION OF AGGREGATION STRUCTURE AND THE RELATIONSHIP WITH MECHANICAL PROPERTIES OF PP MATERIAL

Crystallization Behavior and Mechanical Properties of Poly （lactic Acid）/talc Systems

EFFECTS OF CaCO3 PARTICLE SIZE AND SIZE DISTRIBUTION ON PROPERTY AND STRUCTURE OF PP