Abstract:Talc and PLA-g-maleic anhydride (PLA-g-MAH) were added to polylactide (PLA) to simultaneously improve its melt strength, crystallinity(Xc) and mechanical properties. Using a single. screw extruder with a chaotic mixing screw developed in our group, the PLA-g-MAH was prepared via reactive extrusion. Its grafting rate is measured to be 1%. Then, a series of PLA/talc(5%, 10% and 20%, mass fraction) and PLA/talc(20%, mass fraction) / PLA-g-MAH(5% and 10%, mass fraction) composites were prepared using the same extruder. The chaotic mixing in the extruder effectively improves the dispersion of the talc in the PLA matrix, and the talc of up to 20% almost does not agglomerate. Adding the PLA-g-MAH into the composites reduces the voids and the gaps around the talc on the cyrofractured surfaces and improves the interfacial adhesion between the PLA and talc. For the PLA/talc(20%) composite samples with 10% PLA. g. MAH, the alpha crystal content of the PLA is increased obviously and its Xc is increased to 31.6%. At 175 degrees C, the melt strength for the PLA sample is relatively low(3.6 mN), and it is obviously enhanced(11.6 mN) for the composite sample with 20% talc. The explanation for this is as follows. The well dispersed talc has a rein. forcing effect on the PLA melt and increases the crystallization behavior of PLA; moreover, the draw. down force can improve both effects of the orientation. induced PLA crystallization and the increased PLA crystalliza. tion behavior by the added talc. Compared with the PLA sample, the PLA/talc(20%) /PLA-g-MAH(5%) sample exhibits increments of 51.7% and 16.. 9% for the Young's modulus and impact strength, respectively.

The Effect of Talc on the Mechanical, Crystallization and Foaming Properties of Poly(Lactic Acid)

Effects of talc on the mechanical and thermal properties of polylactide

Preparation and characterization of poly(L-lactide)-co-poly(trimethylene carbonate)/talc film

Mechanical, Barrier, and Thermal Properties of Poly(Lactic Acid)/Poly(Trimethylene Carbonate)/Talc Composite Films

Improving Crystallization Behavior and Melt Strength of Poly(lactic acid) via Adding Talc and PLA-g-MAH

Crystallization improvement of PLA by the talc with "grafting from" method of polymerization of lactide

A strategy to prepare high‐robust and ultra‐tough polylactic acid/polycaprolactone/talc composites with thermo‐resistance

Effect of Dopamine Modified Talcum Powder on the Crystallization Behavior and Rheological Properties of PLA/PBS Blends

Crystallization Behavior and Mechanical Properties of Poly （lactic Acid）/talc Systems

Effects of Inorganic Fillers on the Thermal and Mechanical Properties of Poly(lactic acid).

Preparation and Properties Study of Ultra-fine Talc Filled Poly(Lactic Acid) Films

Introduction of Stereocomplex Crystallites of PLA for the Solid and Microcellular Poly(lactide)/poly(butylene Adipate-Co-terephthalate) Blends

Synergistic Effects of Nucleating Agents and Plasticizers on the Crystallization Behavior of Poly(lactic Acid)

MICRO-STRUCTURE AND MECHANICAL PROPERTIES OF IN-SITU POLYMERIZATION-MODIFIED TALC/PP COMPOSITES

Double-Melting Behavior of Bamboo Fiber/Talc/Poly (Lactic Acid) Composites

Effect of Talc/mma in Situ Polymerization on Mechanical Properties of PVC‐matrix Composites

Effect of in Situ Reaction on Thermal and Mechanical Properties of Polylactide/Talc Composites

Effect of Talc Content on the Degradation of Re-Extruded Polypropylene/talc Composites

Effect of Compatibilizer and Nucleation Agent on the Properties of Poly(lacticacid)/Polycarbonate (PLA/PC) Blends

The effect of talc orientation and transcrystallization on mechanical properties and thermal stability of the polypropylene/talc composites

Intercalated structure of polypropylene/in situ polymerization-modified talc composites via melt compounding