Enhanced Reversibility and Electrochemical Performances of Mechanically Alloyed Cu3P Achieved by Fe Addition

Aijun Zhou,Bin Yang,Weihang Wang,Xinyi Dai,Mingjuan Zhao,Jing Xue,Mangui Han,Cong Fan,Jingze Li

DOI: https://doi.org/10.1039/c6ra01637e

IF: 4.036

2016-01-01

RSC Advances

Abstract:Fe-addition into Cu3P during mechanical alloying enhances the electrode's reversibility by a multi-phase constitute and a refined microstructure.

What problem does this paper attempt to address?

Attaining Exceptional Electrical Conductivity in Cu-Fe Composite by Powder Rolling Strategy

Y. Z. Tian,S. Y. Peng,Y. Yang,X. Y. Pang,S. Li,M. Jiang,H. X. Li,J. W. Wang,G. W. Qin

DOI: https://doi.org/10.1016/j.scriptamat.2023.115302

IF: 6.302

2023-01-01

Scripta Materialia

Abstract:The application of immiscible Cu-Fe composite was limited due to the severe Fe macrosegregation and low electrical conductivity. In this work, bulk Cu-10Fe composite was prepared by powder rolling strategy and further cold rolled to foils. The composition distribution, microstructure evolution, electrical property and me-chanical property were studied. The mutual diffusion of Cu and Fe elements are well controlled during the powder rolling process, such that the good electrical conductivity of the Cu matrix is retained. The Fe particles distribute homogeneously in the Cu matrix, eliminating the Fe macrosegregation phenomenon during the casting process. The Cu-10Fe composite possesses tensile strength of 507 MPa and electrical conductivity of 80.1% IACS. Strengthening mechanisms and origins of exceptional electrical properties were discussed.
Achieving Homogeneous Fe Distribution and High Strength in Cu-Fe Composite Consolidated by Powder Rolling

S. Y. Peng,Y. Z. Tian,Y. Yang,M. Jiang,H. X. Li,J. W. Wang,S. Li,G. W. Qin

DOI: https://doi.org/10.1016/j.msea.2023.145563

2023-01-01

Abstract:The Fe macrosegregation during casting and the limited sample size of the traditional powder metallurgy methods are challenges for the application of Cu-Fe composite. In this work, a powder rolling strategy is developed to fabricate fully dense Cu-10Fe billet by consolidating pure Cu and Fe powders. This method can solve the above problems. The microstructure evolution at different processing stages was characterized in detail by scanning electron microscope (SEM), electron probe microanalysis (EPMA) and transmission electron microscope (TEM). The Fe macrosegregation was avoided and good metallurgical bonding quality between powders was achieved after cold rolling. Ordered clusters were formed in the Fe phase, and three different types of Fe precipitates were found in the Cu matrix. The formation mechanisms of ordered structure and precipitates were analyzed. The variation of mechanical and electrical properties with aging process was discussed.
Effect of Thermomechanical Processing on the Microstructure and Properties of a Cu-Fe-P Alloy

Qiyi Dong,Leinuo Shen,Feng Cao,Yanlin Jia,Kaiju Liao,Mingpu Wang

DOI: https://doi.org/10.1007/s11665-014-1352-6

IF: 2.3

2015-02-24

Journal of Materials Engineering and Performance

Abstract:A Cu-0.7Fe-0.15P (wt.%) alloy was designed, and its comprehensive properties, especially electrical conductivity and temper-softening resistance of the designed alloy, were higher than those of traditional Cu-Fe-P alloys. The microstructure of this alloy was investigated with optical microscopy, scanning electron microscopy, and transmission electron microscopy. The particle of secondary phase was confirmed to be Fe2P with x-ray spectroscopy and digital diffractogram. By virtue of precipitation hardening and work hardening, the tensile strength and electrical conductivity of Cu-0.7Fe-0.15P alloy were 498 MPa and 62% IACS, respectively. The electrical conductivity of this alloy can be up to 92% IACS due to the complete precipitation of Fe2P. After repeating the cold rolling and aging process for three times, the tensile strength, elongation, and conductivity of this alloy were 467 MPa, 22%, and 78% IACS, respectively. Due to the low driving force of recrystallization and the pinning effect of fine dispersed Fe2P, the alloy with low deformation rate showed excellent softening resistance. The designed alloy can be used as a high-strength, high-electrical-conductivity lead-frame alloy.

materials science, multidisciplinary
Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Cheng Cao,Dengbin Chen,Xiaoyang Fang,Jieke Ren,Jianguo Shen,Liang Meng,Jiabin Liu,Lin Qiu,Youtong Fang

DOI: https://doi.org/10.1016/j.jallcom.2020.155175

IF: 6.2

2020-01-01

Journal of Alloys and Compounds

Abstract:Heat exchanger materials with high strength and thin thickness are highly required due to the increasing demands of weight reduction and fuel economy of the automobile. In this work, 0.5 wt% Cu was added to an Al-1.5Mn-0.3Fe-0.6Si (wt.%) alloy to improve the strength. The microstructure, mechanical properties, and electrochemical properties of the tested alloys were systematically investigated. The results suggest that part of Cu is dissolved into the Al matrix, and the balance is incorporated into the Al(Mn,Fe)Si particles. Cu addition improves the strength at the expense of deteriorating the pitting corrosion resistance. On the one hand, the improved strength derives from enhanced solid solution hardening and increased nanoparticle strengthening. On the other hand, the incorporation of Cu in the Al(Mn,Fe)Si intermetallic particles increases the potential difference between the particles and the Al matrix, resulting in the deteriorated pitting corrosion resistance. (c) 2020 Elsevier B.V. All rights reserved.
Effect of Accelerated Fe-Rich Precipitation Induced by Ag Addition on the Microstructure and Comprehensive Properties of Cu–10 Wt Pct Fe Alloys

Junqi Shi,Lun Zhao,Liangguo Chen,Shunran Zhang,Zhongze Lin,Ganpei Tang,Lang Ren,Peijian Shi,Tianxiang Zheng,Yifeng Guo,Qiang Li,Zhe Shen,Biao Ding,Yunbo Zhong

DOI: https://doi.org/10.1007/s11661-022-06927-4

2022-12-20

Metallurgical and Materials Transactions A

Abstract:In this study, the effect of accelerated Fe-rich precipitation caused by Ag addition on the refinement of solidified microstructure and the improvement of electrical, mechanical, and magnetic properties of Cu–10Fe alloys was systematically investigated. Firstly, the quadruple refinement of Cu grains, micron-sized primary Fe-rich spheres and dendrites, and nano-sized Fe-rich precipitates in as-cast Cu–10Fe alloys was induced by the accelerated Fe-rich precipitation. Secondly, the saturation magnetization of as-cast Cu–10Fe alloys was improved, which is mainly dominated by the accelerated precipitation of micron-sized Fe-rich spheres and dendrites, rather than that of nano-sized Fe-rich precipitates. Moreover, the yield strength of cold-rolled Cu–10Fe alloys was increased, which can be attributed to the accelerated precipitation of nano-sized Fe-rich phases and their pinning effect on dislocation movement during cold-rolling. In the end, the synergistic enhancement of strength, ductility, and electrical conductivity of aged Cu–10Fe alloys was obtained by Ag addition, which guides the preparation of high-performance Cu–Fe alloys.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Microstructure and properties of Cu-50Fe alloy produced by chemical co-precipitation and powder metallurgy

Fan Zhu,Xue-ping Gan,Chao-qiang Liu

DOI: https://doi.org/10.1007/s11771-023-5314-8

2023-07-03

Journal of Central South University

Abstract:Traditional casting preparation of Cu-Fe alloy is difficult, especially when Fe content is relatively high, because there is a metastable immiscible region of liquid components between copper (Cu) and iron (Fe), which causes serious compositional segregation in Cu-Fe alloys and leads to low strength and undesirable electrical conductivity of the alloys. In this study, Cu-50Fe alloy was fabricated by chemical co-precipitation and powder metallurgy. Cu-Fe mixed powders prepared by chemical co-precipitation have an average particle size of about 3.5 μm and a near-spherical shape. Copper and iron phases in the fabricated alloy intertwine with each other. After cold deformation, copper and iron phases are elongated along the cold deformation direction to form strips. During aging treatment, a number of Fe particles with diameter of 10–50 nm precipitate in Cu phases in the alloy. The tensile strength and electrical conductivity of the deformed and aged Cu-50Fe alloy are 651 MPa and 41.5%IACS, respectively.

metallurgy & metallurgical engineering
Cu alloying enables superior strength-ductility combination and high corrosion resistance of FeMnCoCr high entropy alloy

Y. Yuan,J.J. Wang,J. Wei,W.Y. Chen,H.L. Yan,N. Jia

DOI: https://doi.org/10.1016/j.jallcom.2023.172543

IF: 6.2

2023-10-24

Journal of Alloys and Compounds

Abstract:The metastable dual phase FeMnCoCr high entropy alloy (HEA) has attracted great attention since it was first proposed, as it can overcome the strength-ductility trade-off at room temperature. For materials in engineering applications, it is also important to achieve high corrosion resistance while maintaining good mechanical properties. In this study, we simultaneously improved the mechanical properties and corrosion resistance of a FeMnCoCr-based HEA via Cu alloying and by applying a simple processing route that combined cold rolling and partial recrystallization annealing. The alloy doped with 0.3 at.% Cu and processed by annealing at 650 °C for 3 min exhibited the best combination of strength and ductility, i.e., yield strength of 768 MPa, tensile strength of 960 MPa and uniform elongation of 33.6%. The high yield strength majorly originated from high density dislocations and grain boundaries in the material, while the formation of deformation twins, martensite laths, stacking faults and Lomer Cottrell locks contributed to the continuous strain hardening and good ductility. The addition of Cu also enhanced corrosion resistance of the HEA in a NaCl solution by improving stability of the alloy matrix and elevating compactness of the passive film. The solid solution of Cu elevated equilibrium potential of the matrix and promotes transformation of microstructure from the face-centered cubic (fcc) plus hexagonal close-packed (hcp) dual phases to the fcc single phase, effectively inhibiting the accelerated corrosion of micro galvanic couple between different phases and enhancing stability of the matrix. At the same time, the enrichment of CuO in the inner layer of the passive film reduced the defect density within the Fe-rich oxide layer, improving the protection of the passive film against the matrix.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Synergistic improvement of mechanical properties and electrical conductivity of Cu-Fe alloys by rare earth metals Sc and Y addition

Xiangyu Yu,Jiawei Ren,Kunhui Gu,Qinwen Zhu,Hanyu Cai,Liangyu Zheng,Wenting Qiu,Guohui Chao,Shen Gong

DOI: https://doi.org/10.1016/j.jallcom.2024.173569

IF: 6.2

2024-04-01

Journal of Alloys and Compounds

Abstract:Cu-4.44Fe-0.26Cr-0.4Si-0.29Mg (CFCSM) alloy and Cu-4.73Fe-0.3Cr-0.38Si-0.28Mg-0.2Sc-0.24Y (CFCSM-Re) alloy were designed. After a series of thermos-mechanical treatment, the alloy has excellent overall properties. The CFCSM-Re alloy had an electrical conductivity of 65%IACS, a yield strength of 552 MPa, a tensile strength of 634 MPa and an elongation of 8.12%. The mechanical properties and electrical conductivity of the alloy were improved by the joint addition of Sc and Y. In comparison with the CFCSM alloy, the conductivity, yield strength, and tensile strength of CFCSM-Re alloy have increased by 0.8% IACS, 124 MPa and 116 MPa, respectively. In CFCSM-Re alloy, dual-scale (Fe, Cr)3Si phase and micron scale Cu(Y, Sc) phase were successfully constructed. CFCSM-Re alloys were strengthened by precipitates, which contributed approximately 50% of total strength. Adding Sc and Y inhibited the alloy’s softening during annealing treatment, resulting in the alloy having high conductivity, high strength, and high elongation. The combined addition of Y and Sc atoms tended to be distributed in positions including vacancy, dislocation, grain boundary and phase interface. Rare earth metals atoms inhibited the movement of dislocations, rotation of grain boundaries and coarsening of precipitates thus endowing CFCSM-Re alloys with excellent strength, elongation and conductivity.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Effects of B Addition on Microstructure Evolution and Efficient Hydrogen Evolution of Self‐Supported Cu–Fe–P Immiscible Alloy

Zhice Xu,Minghou Li,Chengcheng Xu,Chenghe Yan,Yan Ju,Tongtong Liu,Yan Wang,Degang Zhao,Min Zuo

DOI: https://doi.org/10.1002/adem.202400887

IF: 3.6

2024-09-09

Advanced Engineering Materials

Abstract:Herein, it is found that B element has a significant influence on the Marangoni motion of second‐phase in Cu–31.5Fe–4.5P immiscible alloy, resulting in the remarkable refinement of Fe2P and Fe3P secondary particles. The excellent hydrogen evolution reaction catalytic performance of samples can be attributed to the microstructure modification and the significant increase in the electron transfer with B addition. Herein, the effect of B elements on the microstructure and catalytic properties of Cu–31.5Fe–4.5P immiscible alloy is systematically investigated. After microstructure characterizations, it is found that B elements are mainly concentrated in FexP (Fe2P, Fe3P) particles, which affect the Marangoni motion of the particles. With the concentration of B content increasing to 0.75%, the diameter size of the second‐phase particles in the alloys is first refined and then coarsened, in which the alloy with B content of 0.25% has the finest particle size and the proportion of second‐phase particles with sizes ranging from 1 to 10 μm reaches 97%. The electrochemical characterization of dealloyed specimens shows that the overpotential of Cu–Fe–P alloys containing 0.25% B reaches 193 mV at a current density of 10 mA cm−2 in 0.5 m H2SO4 solution. The excellent catalytic performance might be attributed to the increase in the obviously specific surface area of Fe2P and Fe3P particles and the significant increase in the electron transfer.

materials science, multidisciplinary
Influences of Mg and RE on the Microstructure and Properties of Cu-Fe-P Alloy

ZHANG Yu-tian,ZHANG Man,FU Peng-huai

DOI: https://doi.org/10.3969/j.issn.0254-6051.2006.z1.020

2009-01-01

Abstract:Optimization on composition and micro-alloying experiments were carried out on the Cu-Fe-P ally for frame castings.The influences of Mg and RE additions on the structure and the properties during deformation ageing were analyzed.Result showed that by addition of Mg and reduction of the P content,the as cast structure was compose by matrix α-Cu and coarse network sub-structure,the metallic compound,was obtained.After dissolution treatment network structure mainly disappeared instead the coarse grain with fine grain boundary of supersaturated solid solute matrix with small amount of thermo stable phases.A new phase Mg3P2 and dispersed particles would deposit from solid solution after deformation ageing.It was found that with the increase of Mg content the second phase would increase that would affect the properties of alloy after ageing treatment.
Optimizing mechanical and electrical properties of Cu–3Zr alloy by thermomechanical processing

Yan Liang,Xianhui Wang,Yanru Qiu,Yihao Zhang,Yuan Fei,Zhen Li

DOI: https://doi.org/10.1016/j.jmrt.2024.03.098

IF: 6.267

2024-03-21

Journal of Materials Research and Technology

Abstract:Cu–3Zr alloy was prepared by powder metallurgy and two-stage thermomechanical process, and the microstructure evolution and properties were investigated. The results show that the microstructure of as-sintered Cu–3Zr alloy is consisted of the coarse Cu–Zr intermetallic compounds and equiaxed Cu grains. After extrusion, the second phase is smaller in cross section, while deformation texture of the Cu matrix can be seen from longitudinal section. After further drawing, the Cu grains are elongated and the Cu–Zr intermetallic phase is broken into fine particles. The yield strength (YS), ultimate tensile strength (UTS) and electrical conductivity are 593 MPa, 684 MPa, and 74%IACS, which are respectively increased by 38%, 34% and 21% as compared to the as-sintered Cu–3Zr alloy. Phase analysis and microstructural characterization demonstrate that the Cu 5 Zr, Cu 8 Zr 3 , and Cu 10 Zr 7 precipitates are uniformly distributed in the Cu matrix. Cu 5 Zr/Cu and Cu 8 Zr 3 /Cu are combined in the form of coherent relation. Cu 10 Zr 7 /Cu are combined in the form of semi-coherent relation. The enhanced mechanical properties can be attributed to the multiple synergistical strengthening effect. The elongated Cu grains and fine Cu–Zr precipitation phases block the movement of dislocation, resulting in the remarkable enhancement of strength. Moreover, the elongated Cu grains can provide fast channel for the electron transport, giving rise to simultaneous increase of the electrical conductivity.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Microstructural evolution and properties of a Cu-Fe-Mn-P alloys with high strength and high conductivity

Chengzhi Zhang,Xue Xiao,Wendi Yang,Weilin Gao,Qingkui Li,Jilin He

DOI: https://doi.org/10.1016/j.mtcomm.2024.108611

IF: 3.8

2024-03-16

Materials Today Communications

Abstract:A Cu-0.3Fe-0.3Mn-0.16P alloy with high strength and conductivity has been successfully prepared. The influence of integrated multistage thermo-mechanical treatment on the microstructure evolution and properties of the alloy was investigated experimentally. The results reveal substantial production of dislocations and nanosized MnFeP precipitates in the matrix, endowing the alloy with outstanding tensile strength (691 MPa), yield strength (662 MPa), and electrical conductivity (68.0% IACS). Moreover, the Cu-Fe-Mn-P alloy demonstrates excellent softening resistance, particularly at the elevated temperature of 525 °C. The yield strength of the alloy is attributed to strain strengthening, precipitation strengthening, and fine grain strengthening (in decreasing order of importance). Above 600 °C, the alloy exhibited softening behavior marked by recrystallization and the coarsening of precipitates. This research should assist in the development of innovative high-strength and high-conductivity Cu-Fe-Mn-P alloys.

materials science, multidisciplinary
Suppression of discontinuous precipitation by Fe addition in Cu–Ti alloys

Xu Wang,Zhu Xiao,Yu Chen,Zhou Li

DOI: https://doi.org/10.1007/s12598-024-03016-w

IF: 6.318

2024-11-09

Rare Metals

Abstract:Cu–Ti alloys are a kind of elastic copper alloys with excellent comprehensive properties. They are often used in electronic and electrical fields. However, discontinuous precipitation may occur during the preparation process of Cu–Ti alloys, and they can lead to the significant deterioration of mechanical properties. To solve this problem, three Cu–Ti alloys with various Fe contents (Cu–2.7Ti, Cu–2.7Ti–0.1Fe and Cu–2.7Ti–0.2Fe) were designed and prepared in this paper to investigate the effects of Fe on the discontinuous precipitation. The results showed that after aging at any given aging time and temperature, the area fraction of cellular structure decreased with the increase of Fe content. The addition of Fe into Cu–Ti alloys resulted in Fe doping in β'–Cu 4 Ti phase and β–Cu 4 Ti phase. For 450 °C/144 h-aged Cu–2.7Ti–0.2Fe alloy, the Fe content in β'–Cu 4 Ti phase and β–Cu 4 Ti phase was 1.59 at% and 0.90 at%, respectively. The tensile tests showed that under the same aging treatment conditions, Cu–2.7Ti–0.2Fe alloy possessed better mechanical properties. First-principles calculation confirmed that the thermodynamic stability of β'–Cu 4 Ti phase was enhanced by decreasing its cohesive energy through Fe doping. At the same time, the enthalpy of formation of β–Cu 4 Ti phase was generally increased by Fe doping, making it difficult to generate. In short, Fe addition in Cu–Ti alloys suppressed discontinuous precipitation by Fe doping in the precipitates and helped to improve mechanical properties.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Fe microalloying during the in-situ synthesis of homogeneous CuCrFe alloys by aluminothermic Self-propagating

Jin-ru Han,Zhi-he Dou,Ting-an Zhang,Wang An

DOI: https://doi.org/10.1016/j.jmrt.2023.05.225

IF: 6.267

2023-05-29

Journal of Materials Research and Technology

Abstract:Microalloying is an effective approach to improve the performance of CuCr alloys. This paper presents a new idea for the preparation of CuCrFe alloys by self-propagation reduction in-situ microalloying. It is found that the addition of Fe alloying components reduces the Gm and ΔG m of the CuCr melt, which inhibits the occurrence of the liquid phase decomposition process. When the Fe content of CuCrFe alloy is 1.5%, compared with the Cr-rich phase of CuCr alloy, the second phase undergoes significant refinement, the average particle size refined from 21.7 μm to 19.3 μm and the standard deviation reduced from 10.59 to 8.73, and the addition of Fe is beneficial to the spheroidization and refinement of the Cr-rich phase. Fe is mainly combined with Cr, and CuCrFe alloy still exists in the form of two phases. After solution+aging treatment, the average particle size of the second phase in CuCr alloy decreases from 21.8 μm to 17.9 μm, and that in CuCrFe alloy decreases from 19.6 μm to 18.6 μm. The conductivity of CuCrFe alloy increases from 10.5 MS·m -1 to 15.9 MS·m -1 , and the hardness increases from 95.0 HB to 117.0 HB. After heat treatment, the nano-spherical are present in the Cr-rich phase of the CuCrFe alloy, while Fe is completely solid-soluble in the Cr-rich phase; the Cu-rich matrix shows a diffuse distribution of fine second phases, which play a role in strengthening the second phase in the matrix.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Rapid solidification of undercooled FeCoNiCu multi-principal element alloy: Mechanical and tribological properties

Dexu Cui,Jianbao Zhang,Yue Ren,Xuan Luo,Haifeng Wang

DOI: https://doi.org/10.1016/j.jallcom.2021.161806

IF: 6.2

2022-01-01

Journal of Alloys and Compounds

Abstract:A FeCoNiCu multi-principal element alloy (MPEA) was undercooled and its microstructures, mechanical and tribological performance were investigated for different solidification conditions. All the microstructures were consisted of two phases, i.e., the primary Cu-depleted phase and the secondary Cu-rich phase. With the increase of undercooling, a transition of the primary phase from coarse dendrites to fine equiaxed grains happened and the volume fraction of the secondary phase decreased considerably. The primary phase was supersaturated by Cu at high undercooling and segregation of Cu was inhibited considerably by rapid solidification. Consequently, the hardness and yield strength were improved remarkably due to grain refinement strengthening and solution strengthening, and the wear volume was decreased significantly due to both improved mechanical properties and oxidation induced by friction. For the largest undercooling obtained in this study, (i.e., ΔT = 226 K), the yield strength was increased by about 50% and the wear volume was decreased by about 45% as compared with the as-cast case. The current work shows rapid solidification could be an effective way to modulate both mechanical and tribological properties of MPEAs and hence is helpful for their potential applications as engineering materials.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Enhanced Wetting and Properties of Carbon/Copper Composites by Cu-Fe Alloying

Haozi Zuo,Wenfu Wei,Xiaobo Li,Zefeng Yang,Qianhua Liao,Yong Xian,Guangning Wu

DOI: https://doi.org/10.1080/09276440.2021.1904720

IF: 2.839

2022-01-01

Composite Interfaces

Abstract:ABSTRACT Using Fe reaction products to overcome the poor wettability between copper and carbon, C/Cu-Fe composites with excellent properties were prepared by gas pressure infiltration technique. The elemental Fe, being distributed between carbon and Cu, reacted with carbon to form Fe3C layer and effectively improved the wettability of the C/Cu system. The contact angle decreased from 124° to 21°. Compared to composites without Fe doping, the C/Cu-Fe composites exhibit significantly higher compressive and flexural strengths, as well as electrical resistivity reaching six times better than the industry standard requirement. Microstructure analysis indicates that the continuous tight Fe3C interlayer with moderate thickness at the C/Cu interface has a bridge effect on the interfacial bonding enhancement. Graphical abstract
Ultrastrong and ductile FeNi-based alloys through Pd-containing multicomponent L1 2 -type precipitates

Shangkun Shen,Yingxi Li,Liyu Hao,Xuanpu Zhang,Xing Liu,Jinlong Du,Miao Song,Tongde Shen,Engang Fu

DOI: https://doi.org/10.1016/j.matdes.2024.113112

IF: 9.417

2024-06-25

Materials & Design

Abstract:Precipitation strengthening stands as a paramount strategy for enhancing the mechanical properties of FeNi-based alloys. Conventional precipitates used for strengthening typically contain only two major constituent elements selected from Ni, Al, and Ti. However, knowledge about the intrinsic properties and strengthening mechanisms of multicomponent precipitates remains limited. Here, we propose introducing novel multicomponent L1 2 -type precipitates containing palladium (Pd) to strengthen FeNi-based alloys. The strengthened FeNi alloy achieves an eightfold increase in strength compared to the FeNi matrix while maintaining good ductility. Using meticulous micro-characterization and energy-dispersive X-ray spectroscopy (EDS) techniques, in conjunction with first-principles calculations, this study investigated the effects of Pd addition on the thermodynamic stability, morphology, coherency, and strengthening mechanisms of the precipitates. Results indicate that the addition of Pd induces the nucleation of L1 2 -type precipitates, increases their ductility, and eliminates anisotropy in the shear modulus of the precipitates. Excessive Pd content can alter the shape of precipitates from spherical to acicular due to increased interfacial mismatch between the precipitates and the FeNi matrix. These insights shed light on the impact of Pd addition on the intrinsic properties of L1 2 -type precipitates, offering a promising pathway for the design of advanced FeNi-based alloys with optimized mechanical performance.

materials science, multidisciplinary
Study on high-strength and high-conductivity Cu–Fe–P alloys

De-Ping Lu,Jun Wang,Wei-Jun Zeng,Yong Liu,Lei Lu,Bao-De Sun

DOI: https://doi.org/10.1016/j.msea.2006.01.068

2006-04-01

Abstract:A new high-strength and high-conductivity Cu–Fe–P–B–Ce alloy strengthened by cold working and aging was designed. The mechanical properties and electrical conductivity of Cu–Fe–P and Cu–Fe–P–B–Ce alloys were measured, and the microstructures of the samples were analyzed with optical microscope and by transmission electron microscopy. Results showed that the recrystallization temperature of Cu–Fe–P alloy was greatly raised by adding trace B and Ce. Thus, the good strengthening effect processed by both precipitation hardening and cold working hardening was obtained. This novel Cu–Fe–P–B–Ce alloy exhibits excellent combination property that the tensile strength (σb) is 509MPa, the elongation (δ) is 16% and the conductivity is 80% IACS.

materials science, multidisciplinary,nanoscience & nanotechnology,metallurgy & metallurgical engineering
High Strength and High Electrical Conductivity in Cu-Fe Alloys with Nano and Micro Fe Particles

Chenzeng Zhang,Cunguang Chen,Xinhua Liu,Mengjie Yan,Miao Qi,Xuecheng Li,Yang Li,Haifeng Zhang,Fang Yang,Wenwen Wang,Zhimeng Guo

DOI: https://doi.org/10.2139/ssrn.4149411

2022-01-01

SSRN Electronic Journal

Abstract:It is a highly challenge to improve both the strength and electrical conductivity of Cu-Fe alloys (CFAs) simultaneously through the conventional casting method. In this work, one attempt has been conducted to overcome the dilemma via preparing CFAs with ultrafine alloy powders embedded by nano Fe particles. CFA powders with various Fe contents ranging from 5 wt.% to 50 wt.% were synthesized by a novel rapid solidification route named gas-water combined atomization (GWA) process. The GWA alloy powders were then processed by pressureless sintering and multi-pass rolling. The microstructure evolution, mechanical properties and electrical conductivity of CFAs manufactured were investigated in detail. The results showed that GWA alloy powders were nearly spherical, and the mass median diameter (D 50 ) is smaller than 10 μm. Inside the sintered alloy with full density, the average size of initial Fe particles and grains was smaller than 2 μm and 3 μm, respectively. Comparing to pure Cu without Fe particles, the grains of sintered CFAs were obviously refined by the Fe particles, the addition of Fe would increase the stacking fault energy of Cu alloy and inhibited the formation of Cu twins. After rolling, the Fe particles were elongated and fibrous along the rolling direction. The fibrosis degree of Fe particles was enhanced with the increase of Fe content. Cold-rolled CFAs with 5~50 wt.% Fe had the tensile strength of 560~1250 MPa and the conductivity of 33~65% IACS, which indicated that CFAs in this study achieved an optimal balance of mechanical and electrical properties. The microstructure evolution and strengthening mechanisms of CFAs by powder metallurgy (PM) and cold rolling were described. These findings can provide new insights for manufacturing PM CFAs with high performance.
Effect of Mg on microstructure and properties of Cu-Ni-Fe-P alloy with high strength and high conductivity

Jianguo Cui,Rui Zhou,Wendi Yang,Chucan Zhang,Weilin Gao,Jilin He

DOI: https://doi.org/10.1016/j.mtcomm.2024.110513

IF: 3.8

2024-09-27

Materials Today Communications

Abstract:The effect of Mg element on microstructure, strength, conductivity and softening temperature of the Cu-Ni-Fe-P alloy was investigated in details by TEM, EBSD and XRD. The results showed that Cu-0.3Ni-0.3Fe-0.16 P-0.1Mg alloy with high strength and high conductivity was obtained. The tensile strength, microhardness and electrical conductivity of the Cu-Ni-Fe-P-Mg alloy were 692 MPa, 215 HV and 65.2 %IACS, respectively by 90 % cold-rolling(90 %CR) + aging at 450 °C for 4 h + 60 %CR. The microstructure analysis indicated Mg element refined the size of grains and (Ni, Fe) 2 P precipitation phase thus improving the strength of Cu-Ni-Fe-P alloy. The strengthening contributions for Cu-Ni-Fe-P(-Mg) alloys were mainly the precipitation strengthening and dislocation strengthening. In addition, the Cu-Ni-Fe-P-Mg alloy had an excellent softening temperature, as the Mg element delayed the recrystallization of deformed structures because of inhibiting the coarsening of precipitates.

materials science, multidisciplinary

Enhanced Reversibility and Electrochemical Performances of Mechanically Alloyed Cu3P Achieved by Fe Addition

Attaining Exceptional Electrical Conductivity in Cu-Fe Composite by Powder Rolling Strategy

Achieving Homogeneous Fe Distribution and High Strength in Cu-Fe Composite Consolidated by Powder Rolling

Effect of Thermomechanical Processing on the Microstructure and Properties of a Cu-Fe-P Alloy

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Effect of Accelerated Fe-Rich Precipitation Induced by Ag Addition on the Microstructure and Comprehensive Properties of Cu–10 Wt Pct Fe Alloys

Microstructure and properties of Cu-50Fe alloy produced by chemical co-precipitation and powder metallurgy

Cu alloying enables superior strength-ductility combination and high corrosion resistance of FeMnCoCr high entropy alloy

Synergistic improvement of mechanical properties and electrical conductivity of Cu-Fe alloys by rare earth metals Sc and Y addition

Effects of B Addition on Microstructure Evolution and Efficient Hydrogen Evolution of Self‐Supported Cu–Fe–P Immiscible Alloy

Influences of Mg and RE on the Microstructure and Properties of Cu-Fe-P Alloy

Optimizing mechanical and electrical properties of Cu–3Zr alloy by thermomechanical processing

Microstructural evolution and properties of a Cu-Fe-Mn-P alloys with high strength and high conductivity

Suppression of discontinuous precipitation by Fe addition in Cu–Ti alloys

Fe microalloying during the in-situ synthesis of homogeneous CuCrFe alloys by aluminothermic Self-propagating

Rapid solidification of undercooled FeCoNiCu multi-principal element alloy: Mechanical and tribological properties

Enhanced Wetting and Properties of Carbon/Copper Composites by Cu-Fe Alloying

Ultrastrong and ductile FeNi-based alloys through Pd-containing multicomponent L1 2 -type precipitates

Study on high-strength and high-conductivity Cu–Fe–P alloys

High Strength and High Electrical Conductivity in Cu-Fe Alloys with Nano and Micro Fe Particles

Effect of Mg on microstructure and properties of Cu-Ni-Fe-P alloy with high strength and high conductivity