Abstract:<p>Low mechanical strength, especially at high temperatures, is the key problem that limit the application of FeCrAl alloys as the accident tolerance fuel (ATF) cladding materials. Dispersion strengthening by carbide nanoparticles is an effective way to improve mechanical properties at high temperatures. In this work, an ultrafine grained FeCrAl-0.6 wt.% ZrC alloys with excellent mechanical properties were fabricated successfully by mechanical milling and spark plasma sintering. The effect of milling speed on powder characteristics, microstructure and mechanical properties of FeCrAl alloys were investigated. The particle size of the powders increase significantly after milling at 400 rpm, while it has a lower oxygen content. Increasing the milling speed decreased the resultant grain size and improved relative density. Transmission electron microscope (TEM) demonstrated the nano ZrC particles uniformly distributed in the matrix at higher milling speed, which effectively promotes grain refinement and dispersion strengthening. The results of mechanical properties show that the tensile strength, percentage elongation and hardness of FeCrAl-0.6 wt.% ZrC alloys at room temperature (RT) reached up to 1.05 GPa, 349.86 HV and 12.1%, respectively, after milling at 400 rpm. It is worth noting that the FeCrAl-0.6 wt.% ZrC alloy also exhibited a good high-temperature strength more than 110 MPa at 800 ℃, which is about 55.4% and 24.7% higher than previously reported FeCrAl-0.5 wt.% ZrC and FeCrAl-1.0 wt.% ZrC alloys, but the plasticity is reduced. The results demonstrated that the excellent mechanical properties were not only attributed to the dispersion strengthen by nanosized ZrC, a good interface bonding between Fe matrix and nanosized ZrC, but also the ultra-fine grained structure induced by the milling process.</p>

High Strength and High Electrical Conductivity in Cu-Fe Alloys with Nano and Micro Fe Particles

Attaining Exceptional Electrical Conductivity in Cu-Fe Composite by Powder Rolling Strategy

Achieving Homogeneous Fe Distribution and High Strength in Cu-Fe Composite Consolidated by Powder Rolling

Microstructure and Properties of Cold Drawing Cu-2.5% Fe-0.2% Cr and Cu-6% Fe Alloys

Reforming Nanostructured CuAg Alloy to Improve Ductility and Electrical Conductivity

Microstructure and properties of Cu-50Fe alloy produced by chemical co-precipitation and powder metallurgy

Influences of Fe Content and Cold Drawing Strain on the Microstructure and Properties of Powder Metallurgy Cu-Fe Alloy Wire

Developing high performance squeeze cast Al-Cu alloys with high Fe and Cu contents

Enhanced Mechanical Properties of Cast Cu-10 wt%Fe Alloy via Single-Pass Friction Stir Processing

Effects of Fe content on microstructure and properties of Cu–Fe alloy

Microstructure and Properties of High Strength and High Conductivity Cu-0.4Mg Alloy Processed by Upward Continuous Casting and Multi-pass Drawing

Microstructure and properties of FeCoNiCrAl high-entropy alloy particle-reinforced Cu-matrix composites prepared via FSP

Study of high-strength and high-conductivity Cu–Sn–Fe alloys

Achieving high strength and high conductivity synergy through hierarchical precipitation stimulated structural heterogeneities in a Cu-Ag-Zr alloy

Synergistic improvement of mechanical properties and electrical conductivity of Cu-Fe alloys by rare earth metals Sc and Y addition

Enhanced Combination of Strength and Ductility in Ultrafine-Grained Aluminum Composites Reinforced with High Content Intragranular Nanoparticles

Fabrication of ultrafine grained FeCrAl-0.6 wt.% ZrC alloys with enhanced mechanical properties by spark plasma sintering

Effects of Zr-Cu Alloy Powder on Microstructure and Properties of Cu Matrix Composite with Highly-Aligned Flake Graphite

Realizing the combination of high strength and good ductility of Cu matrix composites with CrCoNi reinforcement particles and microlaminated structure

Effect of Thermomechanical Processing on the Microstructure and Properties of a Cu-Fe-P Alloy

Effect of Fe content on low cycle fatigue behavior of squeeze cast Al-Zn-Mg-Cu alloys