Abstract:Abstract The effect of Mg alloying on microstructure and mechanical properties at 300 °C of Al–5Cu–1Mn–0.5Ni heat-resistant aluminum alloy was investigated by microstructure observation and tensile test. Alloying with 0.5 wt%Mg addition considerably increases the yield strength at 300 °C of samples at as-cast, as-solutionized and as-aged states. It also greatly enhances the strengthening effects from solution and ageing treatments, however, simultaneously, decreases the elongation greatly. During the solidification process of the alloy with Mg addition, a great amount of whisker-like Al–Cu–Mg compound phase is formed at the eutectic boundary zones in the form of ridge configuration, which is determined as AlCuMg intermetallic compound by TEM. During the solution treatment, this whisker-like AlCuMg phase is completely dissolved into Al matrix that leads to a remarkable rise in the increment of yield strength at 300 °C by solution strengthening. The alloying of Mg has a significant influence on the precipitation behavior during the ageing treatment, for examples, promoting the formation of finer θ ′′ particles and a great number of Cu–Mg atomic clusters. During high temperature tensile test, theses clusters evolve into fine cube-like Al 5 Cu 2 Mg particles with orthorhombic structure. It is the significant microstructure evolution induced by alloying of Mg that leads to the great rise in yield strength at 300 °C. Addition of Mg in Al–Cu–Mn–Ni alloy dose not lead to the formation of meta-stable or stable S phase, but whisker-like AlCuMg and cube-like Al 5 Cu 2 Mg compounds are determined by TEM.

Effect of Mg on microstructure and properties of Cu-Ni-Fe-P alloy with high strength and high conductivity

Microstructural evolution and properties of a Cu-Fe-Mn-P alloys with high strength and high conductivity

Effects of Zr and Mg alloying on microstructure and properties of Cu-Cr-Si alloys

Synergistical Effects of Mg Microalloying, Deformation, and Aging on the Strength and Electrical Conductivity of Cu‐3.3 wt%Ti Alloy

Microstructure and Properties of High Strength and High Conductivity Cu-0.4Mg Alloy Processed by Upward Continuous Casting and Multi-pass Drawing

Effect of Thermomechanical Processing on the Microstructure and Properties of a Cu-Fe-P Alloy

Alloying effect of Mg on microstructure and mechanical properties at 300 °C of Al–5Cu–1Mn–0.5Ni heat-resistant alloy

Evolution of the microstructure and properties of a Cu–Cr-(Mg) Alloy upon thermomechanical treatment

Microstructure and Properties of Cold Drawing Cu-2.5% Fe-0.2% Cr and Cu-6% Fe Alloys

Effects of Mg content on microstructure and mechanical properties of low Zn-containing Al−xMg−3Zn−1Cu cast alloys

Influences of Mg and RE on the Microstructure and Properties of Cu-Fe-P Alloy

Study on the effect of enhanced magnesium and copper contents on microstructure and property of Al-Zn-Mg-Cu alloys with high zinc element content during fabrication processes

Microstructure and Precipitate's Characterization of the Cu-Ni-Si-P Alloy

Microstructure and thermophysical properties of Mg-2Zn-xCu alloys

Influence of Ni-P content on microstructure and mechanical properties of Fe-x(Ni+P)-1Cu alloys

Effect of Cold Rolling and Aging Treatment on the Microstructure and Properties of Cu–3Ti–2Mg Alloy

Effect of Mg addition on microstructure and mechanical properties of Al-Si-Cu-Fe alloy with squeeze casting

Study on properties and precipitation behavior of 6000 series alloys with high Mg/Si ratios and Cu contents

Effects of Cu and Mn on Mechanical Properties and Damping Capacity of Mg-Cu-Mn Alloy

Study on high-strength and high-conductivity Cu–Fe–P alloys

An Insight into Mg Alloying Effects on Cu Thin Films:Microstructural Evolution and Mechanical Behavior