Abstract:Summary Hydraulic fracturing is an effective stimulation method to establish high-conductivity channels in tight reservoirs, and the effectiveness of man-made fractures largely depends on the proppant-carrying capacity of the fracturing fluids used. As a novel completion fluid, silica gel-based fracturing fluids have shown desirable stimulation effect in application cases, but a comprehensive evaluation of their proppant settling and transport behaviors in the laboratory remains lacking. In this paper, a silica gel-based fracturing fluid was prepared first, and then the rheological properties, including shear thinning, recovery behavior, and viscoelasticity of the fluid system, were measured. Afterward, the settling velocity of single-particle proppant and the settling rate of multiparticle proppant under various experimental conditions were investigated in the static fluid system; in addition, the dynamic proppant-carrying performance was evaluated using a visualized rough fracture model to study different factors on the dune distribution inside the fractures. Lastly, the proppant-carrying mechanism of silica gel-based fracturing fluid was revealed in three aspects. The rheological test result showed that the shear viscosity of silica gel-based fracturing fluid increased as the SiO2 concentration increased. Furthermore, all tested fluid samples exhibited an elastic modulus that is consistently greater than the viscous modulus, indicating that the silica gel-based fracturing fluid system has a dominant elastic response behavior. In the single-particle static settling test, there was a significant increase in the settling velocities as the particle diameter increased and as the temperature increased. Meanwhile, the settling rate of multiparticles showed a decreasing trend with the increase in mesh size, while the proppant settling rate gradually increased as the proppant concentration rose. The results of dynamic proppant-carrying experiments demonstrate that a higher pumping rate leads to an extended migration distance for proppant, resulting in formed sand dunes with reduced height within fractures. Conversely, an increase in proppant concentration and a reduction in mesh size tend to form higher sand dunes. The proppant-carrying mechanisms of the silica gel-based fracturing fluid relate to the self-polymerization and syneresis of silica gel, the noticeable elasticity characteristics, and the structural encapsulation effect formed between silica gel and proppant. A better understanding of the proppant settling and transport behaviors of silica gel-based fracturing fluid can be helpful in optimizing the hydraulic fracturing design and promoting field application.

Experimental investigation on the flow properties of sand granules in the process of sand mold printing

Investigation on Moist Silica Sand's Circulation for Sand Mold Printing with Line-Forming

Coating Process of Multi-Material Composite Sand Mold 3D Printing

Experimental investigation on the performance and mesostructure of multi-material composite 3D-printed sand mold

Fabrication and posttreatment for inorganic binder jetting sand molds for casting

Digital High-Efficiency Print Forming Method and Device for Multi-Material Casting Molds

Wetting characteristic and flow behavior of silicate binder at various sand particle-particle interfaces: Fine or coarse, circular or angular particles

Integrated manufacturing method of multimaterial sand mold by binder jetting

Research on Key Technique of Line Forming for 3D Sand Mould Printing Based on Quantitative Analysis of Binder Content

Investigation of Selected Parameters Effect on 3D Printed Sand Mold Properties Through Taguchi Method

Rheology and Yield Stress Evolution of Highly Flowable Cementitious Grouting Materials: Mechanisms and Modeling

Relation Between Rheological and Curing Behavior of Inorganic Foam Slurries in the Gel-Casting Process

Experimental Research on the Proppant Settling and Transport Characteristics of Silica Gel-Based Fracturing Fluid

Experimental research on the glass fiber-reinforced effect and mechanisms of sand powder 3D-printed rock-like materials

Micromechanism study on the influence of particle deposition angle on mechanical properties of sand

Effect of Carbon Dioxide Temperature on Adhesion of Na2SiO3 Binder to Silica Sand Surface: Comparison of Experimental Data with Molecular Dynamics Simulations

Mechanisms affecting viscosity of cement paste made with microfines of manufactured sand

Study of Affecting Factors on Porosity in Gel-Casting Foam

The Rheological Behaviors and Overcuring Effect of Fiber-Reinforced Polyamine-Coated Silica Paste and the Mechanical Properties of the Composites Via Stereolithography

Flowloop investigation into hydrate formation and slurry flow in the presence of micron-sized sand particles

Comparative study on the mechanical properties of solidified silty-fine sand reinforced by permeable polymer and traditional grouting materials