Abstract:Three-dimensional (3D) printing has been increasingly applied to experimental research in geotechnical engineering. In this paper, standard cylinder specimens with high and low strength were prepared using 3D-printing sand core technology. The elastic-plastic and rheological mechanical behaviors were experimentally studied. In addition, the similarity and limitations were verified through comparison with natural sandstone, slate, sand-gypsum, claystone, etc. On this basis, a new way to prepare soft-hard interbedded layered rock in geotechnical mechanics was developed. Considering the features of layered rock and the principle of 3D printing, cylindrical and cubic specimens of soft-hard interlayered rock mass with different inclination angles were prepared by controlling the binder content layer by layer. The deformation and strain differences between the soft and hard phases were verified through digital image correlation. In this case, the anisotropic failure evolution mode of soft-hard interbedded rock mass was revealed by the images captured. The structural anisotropy behaviors of 3D-printed soft-hard interbedded rock was also studied. The results agree well with the published experimental and theoretical results. This study introduces a broad prospect of 3D printing sand core technology for future experimental mechanical research on a soft-hard interbedded layered rock mass in geotechnical engineering. This study developed a new method for preparing soft-hard interbedded rock masses based on 3D printing sand core technology. The elastic-plastic and rheological characteristics of 3D-printed soft rock, hard rock, and soft-hard interbedded rock were investigated and compared with a natural layered rock mass. Moreover, the deformation and strain differences between the soft and hard phases were verified from a mesoscopic perspective. The structural anisotropy behaviors and anisotropic failure mode of soft-hard interbedded rock mass were revealed. The results agreed well with the published experimental and theoretical results. Thus, specimens with complex structures, such as soft-hard interbedded rock mass, could be prepared with 3D printing sand core technology. As a result, the mechanical parameters of 3D-printed specimens were close to those of sandy mudstone and claystone rock masses, while the trends of the stress-strain curves of 3D-printed specimens were consistent with natural sandstone rock masses. This study brings a broad prospect for future investigation of the soft-hard interbedded layered rock mass in actual geotechnical engineering.

Experimental research on the glass fiber-reinforced effect and mechanisms of sand powder 3D-printed rock-like materials

Investigation of 3D Printing Sand Core Technology on the Mechanical Behaviors of Soft–Hard Interbedded Rock Masses

Characteristics and mechanism of time on sand powder 3D printing rock analogue: a new method for fractured rock mechanics

Experimental Investigation into the Mechanical Behavior of Jointed Soft Rock Using Sand Powder 3D Printing

Microstructure and Mechanical Behavior of 3D Printed Rock-Like Specimens Based on Different Post-Processing Methods

A Comprehensive Experimental Study on Mechanical Behavior, Microstructure and Transport Properties of 3D-printed Rock Analogs

Preliminary Study on Size Effect of Fractured Rock Mass with Sand Powder 3D Printing

Application and prospective of sand-type 3D printing material in rock mechanics: a review

Investigation on Mechanical Properties Regulation of Rock-Like Specimens Based on 3D Printing and Similarity Quantification

Experimental investigation on the performance and mesostructure of multi-material composite 3D-printed sand mold

Effect of fractures on mechanical behavior of sand powder 3D printing rock analogue under triaxial compression

Study on mechanical properties of 3D printed rock mass samples with photosensitive resin material

Experimental Study on the Size Effect and Anisotropy in Mechanical Properties of Fractured Rock Mass based on 3D Printing

In-situ X-CT scanning and numerical modeling on the mechanical behavior of the 3D printing rock

The 3D-Printing Technology of Geological Models Using Rock-Like Materials

Fundamental Study on Applicability of Powder-Based 3D Printer for Physical Modeling in Rock Mechanics

Experimental Study of Multi-Angle Effects of Micron-Silica Fume on Micro-Pore Structure and Macroscopic Mechanical Properties of Rock-like Material Based on NMR and SEM

3D Printing for Experiments in Petrophysics, Rock Physics, and Rock Mechanics: A Review

Nanoscale mechanical properties of 3D printed gypsum-powder-based rocks by nanoindentation and numerical modeling

Modification effect of nanosilica and polypropylene fiber for extrusion-based 3D printing concrete: Printability and mechanical anisotropy

Application and prospects of 3D printing in physical experiments of rock mass mechanics and engineering: materials, methodologies and models