Abstract:The use of carbon fiber reinforced plastic (CFRP) is rapidly increasing in aerospace and automobile applications. This is in large part due to the increase strength and modulus of carbon fiber composites compared to other materials such as glass fiber composites. The fiber-matrix interface has been found to be important for high strength in composites. Methods that have been studied and developed to improve interfacial property of composites include: the addition of coupling agents, surface modifications, chemical reaction control and use of nano-fillers for reinforcement. During mechanical loading the shape of carbon fibers, in a composite, is altered with a concomitant change in electrical resistance. Carbon fibers are used as sensing elements in CFRP due to their electrical conductivity. In some more advanced studies, in CRFP, the carbon fibers were used for both strain sensing and damage sensing. The basic theory, in such studies, was that the movement of carbon fiber could be detected by electrical resistance measurement. During loading, the extent of contact between carbon fibers in a CF tow is altered, and the electrical resistance changes from its initial value. In this work, interfacial properties of carbon fiber/polymer composites were evaluated by such electrical resistance measurements. During the wetting process of CF tows by the polymer resins, the change in electrical resistance was recorded and analyzed. The test results for different carbon fibers and polymer resins exhibited different trends. The electrical resistance change was associated with the different wetting conditions, and the interfacial properties were predicted by these electrical resistance measurements. CF tow/epoxy exhibited the poorest carbon tow wettability, the smallest change in resistance and the poorest IFSS and ILSS. For the four systems studied, the relative change in each of these quantities for the materials of a given composite was roughly proportional to the other measured quantities. This may have some very significant practical importance. It may point the way to use quick easy tests to screen and predict other behaviors for composites of different materials and/or processes. Perhaps a simple resistance change test might be used to predict and select good candidate materials, surface processing techniques for high strength composite applications. The proportional relationship between interfacial adhesion and electrical resistance change was obtained by trend fitting line analyses. Ultimately, it was demonstrated that mechanical properties related to interfacial properties might potentially be predicted by electrical resistance measurement and studies of wetting behavior, using empirical formulas and correlations.

Detection of Bending Direction and Amplitude by Electrical Resistance Measurement of Axial Carbon Fibers in Braided Composite Tube

A New Electrical Resistance Measurement Method of Carbon Fiber-Reinforced Polymer Tubes Based on C⁴D Technique

Modelling of Concrete-Filled Filament-Wound FRP Confining Tubes Considering Nonlinear Biaxial Tube Behavior

Self-Sensing Of Position-Related Loads In Continuous Carbon Fibers-Embedded 3d-Printed Polymer Structures Using Electrical Resistance Measurement

Interfacial Evaluation Of Carbon Frinforced Nano-Composites Using Electrical Resistance Measurement With Wetting Tests

New Method for Interfacial Evaluation of Carbon Fiber/Thermosetting Composites by Wetting and Electrical Resistance Measurements

Real-time self-monitoring and smart bend recognizing of fiber-reinforced polymer composites enabled by embedded magnetic fibers

Tensile damage self-monitoring of carbon fiber/epoxy 3D braided composites with electrical resistance method

X-ray microtomography analysis of the damage mechanisms in 3D circular braided carbon fiber/epoxy resin composite tubes under axial impact compression

Experimental Investigation of Self-Sensing Carbon Fiber Reinforced Cementitious Composite for Strain Measurement of an RC Portal Frame

Measurement of the Flexural Modulus of Chopped Carbon Fiber Tape Reinforced Thermoplastic with Short Beams

Characteristic analysis of carbon nanotube thread embedded into three-dimensional braided composite under bending load

An Investigation into Self-Sensing Property of Hat-Shaped 3D Orthogonal Woven Composite under Bending Test

Analysis-oriented Model for FRP Tube-Confined Concrete: 3D Interpretation of Biaxial Tube Behaviour

Corrosion monitoring of PC beams with a novel type of HCFRP sensors

EFFECT OF TRANSVERSE/AXIAL FIBER RATIOS ON THE FLEXURAL CAPACITY OF CONCRETE-FILLED FRP TUBE BEAMS

Carbon Rovings as Strain Sensor in TRC Structures: Effect of Roving Cross-Sectional Shape and Coating Material on the Electrical Response under Bending Stress

Tensile strain and damage self-sensing of flax FRP laminates using carbon nanofiber conductive network coupled with acoustic emission

The synergetic relation of flexural strain behaviors and electrical signals of carbon nanotube-based polymer laminates

Textile-based strain sensors for fiber-reinforced composites under tension, compression and bending

Pure Directional Bending Measurement With a Fiber Bragg Grating at the Connection Joint of Eccentric-Core and Single-Mode Fibers