Abstract:TiAl intermetallic compounds, as a new kind of high-performance light-weight structural material, are widely applied in many fields. Titanium carbide (TiC) as the reinforcing phase could improve the mechanical properties, wear resistance, and heat-resistance stability of TiAl intermetallic compounds. Ti(Al, C) mixture powders were deposited by cold spraying at gas temperature of 250 °C, 450 °C, and 550 °C. Then, Ti(Al, C) coatings were annealed at temperatures of 650 °C for different times and following holding at 1100 °C for 3 h. The microstructure, microhardness, fracture toughness, and abrasive wear of Ti-Al composite coatings were investigated. The research results were that the particle size of mixture powders decreased as the ball milling time prolonging. Ti(Al) solid solution appeared in the mixture powders as the milling time increased to 30 h. The average porosity of the coating sprayed at 550 °C was the lowest (0.85%). The as-sprayed coatings exhibited the same phase compositions with the mixture powders. The coating sprayed at gas temperature of 550 °C has the highest microhardness and the lowest weight loss. Ti-Al intermetallic was in-situ synthesized after annealing at 650 °C. The average porosity of the annealed coating (sprayed at 450 °C) was the lowest. The content of Ti-Al intermetallic compounds of the annealed coating sprayed at 450 °C is the highest. The X-ray diffraction (XRD) analysis results are consistent with the EDS analysis of the annealed coatings after annealing at 650 °C. Ti-Al intermetallic compounds were almost completely formed in the three kinds of the coatings after annealing at 650 °C for 20 h and following holding at 1100 °C for 3 h. TiAl and TiAl3 intermetallic phases were in-situ synthesized in the coatings based on the energy dispersive spectroscopy (EDS) and XRD analysis. TiC was also in situ synthesized in the coatings as the annealing temperature increased to 1100 °C. The annealed coating (sprayed at 450 °C) has the highest microhardness, fracture toughness, and wear resistance properties after annealing at 1100 °C for 3 h.

Microstructure and Mechanical Properties of TiC-Fe Surface Gradient Coating on a Pure Titanium Substrate Prepared in Situ

TiC-Fe gradient coating on pure titanium fabricated by in-situ solid-phase diffusion: Toward superior hardness and interfacial adhesion strength

Microstructure and Fracture Toughness of Compact TiC-Fe Gradient Coating Fabricated on Cast Iron Substrate by Two-Step in Situ Reaction

TiC–Fe gradient coating with high hardness and interfacial adhesion strength on cast iron prepared by in-situ solid-phase diffusion method

Investigation on Microstructure and Wear Properties of an <i>In Situ</i> Synthesized TiC Gradient Coating

Preparation of a gradient nanostructured surface TaC layer-reinforced Fe substrate by in situ reaction

A Key to Tune the Grain Size Gradient of the TiC Coating on Titanium by Interstitial Carburization: the Timing for Pressing

Microstructure Formation and Mechanical Properties of Metastable Titanium-Based Gradient Coating Fabricated via Intense Pulse Ion Beam Melt Mixing

Microstructure Evolution and Mechanical Properties of TiC/Ti6Al4V Medical Composite Processed by Severe Plastic Deformation

In situ formation by laser cladding of a TiC composite coating with a gradient distribution

Microstructure, Formation Mechanism and Mechanical Properties of ZrC–Fe Coating on Cast Iron Via in Situ Solid-Phase Diffusion

Crack Resistance Enhancement of Gradient Bias TiN/Ti Multilayer Coating by Ti Sputtering

Structure and mechanical properties of graded Cr/CrN/CrTiN coatings synthesized by close field unbalanced magnetron sputtering

Microstructure, Microhardness, Fracture Toughness, and Abrasive Wear of In-Situ Synthesized TiC/Ti-Al Composite Coatings by Cold Spraying Combined with Heat Treatment

Microstructure Evolution of TiC Particles In Situ, Synthesized by Laser Cladding

Research on Microstructure and Formation Mechanism of TiC Particles Reinforced Iron Matrix Surface Gradient Composite by In-situ Technology

Characterization of Surface Properties of TiC Ceramic Coating Developed on AISI 1020 Steel

In-situ Ti(C, N) reinforced AlCoCrFeNiSi-based high entropy alloy coating with functional gradient double-layer structure fabricated by laser cladding

In Situ Formation of Tic Particulate Composite Coating with A Gradient Distribution by Laser Cladding

Microstructural evolution, mechanical properties and wear behavior of in-situ TiC-reinforced Ti matrix composite coating by induction cladding

Abrasive wear characteristics of in-situ TiC-reinforced iron matrix surface gradient composites