Abstract:Functional gradient materials (FGM), with their composition gradually varied in different positions, have attracted much attention for research and development during the years. Normally there are two types of functional gradient materials: one without the formation of intermetallics which is easier for fabrication due to less scientific and technological challenge; the other one with the formation of intermetallics in some part of the gradient changed composition range such as Ti-Al, Ti-Fe, Ni-Al gradient materials, which still exists big challenge on intermetallic, resulting in high brittleness and unavailability.Laser deposition is a competitive candidate for FGM due to its capability on accurate composition and precise dimension control. According to an aeronautical application requirement to gradually change the composition from Ti6Al4V to 316L, this paper reports on laser deposition of Ti6Al4V to 316L gradient composition structure. A big challenge is the formation of the TiFe intermetallic especially near the composition of Ti50Fe50, which results in very high cracking tendency. Many efforts have been made to optimize the Ti-Fe composition ratio, the deposition process and the deposition parameters, not a single Ti6Al4V-316L composition gradient structure was successful due to the formation of the very brittle TiFe and TiFe2 intermetallics. This indicates that it is almost impossible to direct deposit Ti6Al4V to 316L without cracking and separation. We used Inconel 625 powder as an interlayer between the Ti6Al4V and the 316L, thus a sound Ti6Al4V-316L composition gradient structure was successfully achieved by laser deposition. The brittle TiFe and TiFe2 intermetallics were replaced by a series of phase evolutions: α+β → β+Ti2Ni→Ti2Ni+TiNi→TiNi→TiNi+TiNi3→Ni3Fe→ Ni2Fe3→γFe. The brittleness was dramatically decreased or diluted and crack-free composition gradient structure was available. The gradient structure was further analyzed on hardness, microstructural evolution, the Young's modulus and Poisson's ratio.

Microstructure Evolution and Mechanical Properties of TiC/Ti6Al4V Medical Composite Processed by Severe Plastic Deformation

Surface modification and twinning behavior in gradient graphene-based TiC/Ti6Al4V composite

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

Study on Microstructure and Properties of Additive-Manufactured TC4ELI+TC21 Titanium Alloy Gradient Composite Structures

Microdeformation and strengthening mechanism of 3D printed TC4/TC11 gradient titanium alloy subjected to tensile loading

Strength-toughness matching mechanisms of a boride-reinforced Ti6Al4V compositionally graded material fabricated using spark plasma sintering

A strong, machinable, and multifunctional Ti3SiC2-(Ti3SiC2-Cf) composite: Gradient architecture and mechanical properties

Microstructural Evolution and Deformation Mechanisms of in‐situ TiC Reinforced Ti‐6Al‐4V Composites during High‐Temperature Hot Compression

Effects of TiB2 content and gradient structure on microstructural characterization and mechanical properties of TiB2/Al7050 composites

Microstructure evolution and improved properties of laminated titanium matrix composites with gradient equiaxed grains

Anisotropic microstructures and mechanical properties of textured Ti3AlC2/TiAl3/Al composite

Laser Deposition of Ti6Al4V-316L Composition Gradient Structure: Challenge on Intermetallics

TiC-Fe gradient coating on pure titanium fabricated by in-situ solid-phase diffusion: Toward superior hardness and interfacial adhesion strength

On Dynamic Recrystallization during the Friction Stir Processing of Commercially Pure Ti and Its Influence on the Microstructure and Mechanical Properties

Densification, Microstructure and Mechanical Performance of TiC/Fe Composites by Spark Plasma Sintering

Fundamental Study of In-Situ Strengthening and Formation of Continuous Gradient Titanium Alloys via Laser Directed Energy Deposition

Gradient microstructure and mechanical properties of Ti-6Al-4V titanium alloy fabricated by high-frequency induction quenching treatment

Graded microstructure and mechanical properties of additive manufactured Ti–6Al–4V via electron beam melting

Effect of TiC Content on Mechanical Properties and Microstructure Evolution of TiC/Inconel 718 Functionally Gradient Materials by Direct Energy Deposition

Evolution of microstructure, macrotexture and mechanical properties of high strength biomedical TA4 pure titanium during multi-pass ECAP

Microstructure and mechanical properties of TC4/NiTi bionic gradient heterogeneous alloy prepared by multi-wire arc additive manufacturing