Abstract:Thermal conductivity of SiCp/Cu composites was usually far below the expectation, which is usually attributed to the low real thermal conductivity of matrix. In the present work, highly pure Cu matrix composites reinforced with acid washed SiC particles were prepared by the pressure infiltration method. The interfacial microstructure of SiCp/Cu composites was characterized by layered interfacial products, including un-reacted SiC particles, a Cu-Si layer, a polycrystalline C layer and Cu-Si matrix. However, no Cu3Si was found in the present work, which is evidence for the hypothesis that the formation of Cu3Si phase in SiC/Cu system might be related to the alloying elements in Cu matrix and residual Si in SiC particles. The thermal conductivity of SiCp/Cu composites was slightly increased with the particle size from 69.9 to 78.6 W/(m K). Due to high density defects, the real thermal conductivity of Cu matrix calculated by H-J model was only about 70 W/(m K). The significant decrease in thermal conductivity of Cu matrix is an important factor for the low thermal conductivity of SiCp/Cu composites. However, even considered the significant decrease of thermal conductivity of Cu matrix, theoretical values of SiCp/Cu composites calculated by H-J model were still higher than the experimental results. Therefore, an ideal particle was introduced in the present work to evaluate the effect of interfacial thermal resistance. The reverse-deduced effective thermal conductivities of ideal particles according to H-J model was about 80 W/(m K). Therefore, severe interfacial reaction in SiCp/Cu composites also leads to the low thermal conductivity of SiCp/Cu composites. (C) 2014 Elsevier Ltd. All rights reserved.

Co-deposition of Nano-Size SiC Particles in Micro-Via

Experimental Analysis Of The Co-Deposition Of Metal Cu And Nano-Sized Sic Particles With Ctab In Micro Via Filling

Dual Effects of CTAB on Co-deposition of SiC/Cu in Micro Via

Carbon Nanotube Vias: Does Ballistic Electron–Phonon Transport Imply Improved Performance and Reliability?

Filling Technique Of Through Silicon Via By Co-Depositing Copper And Sic Nano-Particles

Enhanced thermal expansion with nanocrystalline Cu in SiO 2 vias for hybrid bonding

Development of SiC Composite Solder with Low CTE as Filling Material for Molten Metal TSV Filling

Three-dimensional Simulation of Effects of Microstructure Evolution and Interfacial Delamination on Cu Protrusion in Copper Filled Through Silicon Vias by Combined Monte Carlo and Finite Element Methods

Carbon Nanotube/Copper composites for via filling and thermal management

Microstructure and thermal properties of SiCp/Cu composites with Mo coating on SiC particles

Investigation of SiC Nanoparticle Size and Distribution Effects on Microstructure and Mechanical Properties of Al/SiC/Cu Composite during the FSSW Process: Experimental and Simulation

Development of a Polyimide/SiC-Whisker/Nano-Particles Composite with High Thermal Conductivity and Low Coefficient of Thermal Expansion As Dielectric Layer for Interposer Application

Microstructural Evolution and Degradation Mechanism of SiC–Cu Chip Attachment Using Sintered Nano-Ag Paste During High-Temperature Ageing

Study of a through-silicon/substrate via filling method based on the combinative effect of capillary action and liquid bridge rupture

Interfacial microstructure and its effect on thermal conductivity of SiCp/Cu composites

Fabrication and Properties of SiC/Cu Composites for Electronic Packaging

Microstructure Simulation and Thermo-Mechanical Behavior Analysis of Cu-filled Through Silicon Vias (tsvs) Using Combined Monte Carlo and Finite Element Method

Copper Filling Process for Small Diameter, High Aspect Ratio Through Silicon Via (Tsv)

High-temperature Resistant Interconnections Formed by Ni Nanoparticles/Al Micro-particles Composite Paste for SiC Power Device Application

Investigate the Microstructure Changes in Cu Through-Silicon Vias (tsvs) under Thermal Process

Reactions Mechanism and Mechanical Properties of a SiCf/SiC Joint Affected by Cu/Ni/Ti Elements and Inhomogeneous Composites