Abstract:In this paper, flexible and deployable double-sided linear-to-circular polarizers designed on polydimethylsiloxane are proposed for the first time to the best of our knowledge. Shieldlt textile is used as the conducting element of the two designs based on two different unit cell arrays: a loaded circular patch unit cell or an unloaded circular patch unit cell, both backed by a generic rectangular element on its reverse side. This is in contrast to conventional frequency-selective structure-based linear-to-circular polarizers implemented using rigid substrates, which are multi-layered and requires inter-layer physical spacing. This complicates their implementation using flexible substrates and in a deployable format. Upon implementation of this double-sided polarizer, their final performances are evaluated in terms of the phase difference, conversion efficiency, 3-dB axial ratio (AR), and ellipticity bandwidth (from 40 degrees to 45 degrees). Measurements indicated good agreements with simulations, and both structures exhibited more than 90% of conversion efficiency from 2.34 to 3 GHz (for the loaded circular unit cell) and from 2.36 to 3 GHz (for the unloaded circular unit cell). In terms of ellipticity, a bandwidth of 8.67% is observed for the unloaded design and 13.82% for the loaded design. The unloaded structure exhibited a fractional 3-dB AR bandwidth of 36.36% (from 1.98 to 2.86 GHz) in simulations, and 32.64 % (from 2.00 to 2.78 GHz) when evaluated experimentally. Conversely, the loaded design showed only 12.58%. An equivalent circuit model is proposed and validated via a comparison between the circuit and full-wave simulations. Finally, the performances of these polarizers are also assessed under different bending conditions due to the use of flexible materials, prior to the proposal of a suitable deployment mechanism.

Single Layered Swastika-Shaped Flexible Linear-to-circular Polarizer Using Textiles for S-band Application

Circuit Model for a Textile Linear-to-Circular Polarizer Using Swastika-Shaped FSS

Deployable Linear-to-Circular Polarizer Using PDMS Based on Unloaded and Loaded Circular FSS Arrays for Pico-Satellites.

A Crossed Dodecagonal Deployable Polarizer on Textile and Polydimethylsiloxane (PDMS) Substrates

Polarization Control by Using Anisotropic 3-D Chiral Structures

A Highly Tunable Sub-Wavelength Chiral Structure For Circular Polarizer

A Wideband Linear-to-Circular Polarizer Based on Hexagonal FSS on PDMS Substrate for CubeSats

A Flexible Wearable Linear-to-Circular Polarizer for GNSS Application

A modified dumbbell-shaped highly efficient broadband multifunctional polarizer for X and Ku band applications

Novel Broad Band FSS Dual-Layer Circular Polarizer Based on Quarter Wave Plate

Microwave Polarizer Based on Complementary Split Ring Resonators Frequency-Selective Surface for Conformal Application

Broadband linear‐cross and circular‐circular polarizers with minimal bandwidth reduction at higher oblique angles for RCS applications

Linear and circular-polarization conversion in X-band using anisotropic metasurface

An Ultrawideband Linear-to-Circular Polarizer Based on a Phase Difference Complementary Scheme

A Broadband Ultra-Thin Polarization Rotator Using Periodically Loaded Parallel Strip-Lines

Single layer dual wideband linear to circular polarisation converter with integrated parasitic elements

Multi-band ultrathin reflective metasurface for linear and circular polarization conversion in Ku, K, and Ka bands

A Multiband and Multifunctional Metasurface for Linear and Circular Polarization Conversion in Reflection Modes

A Metasurface-Based LTC Polarization Converter with S-Shaped Split Ring Resonator Structure for Flexible Applications

Solar-Panel Integrated Circularly Polarized Meshed Patch for Cubesats and Other Small Satellites

A Dual‐band Linear‐to‐circular Polarization Converter with Robustness under Oblique Incidences