Abstract:Thermal atomic layer etching (ALE) of molybdenum (Mo) was demonstrated using sequential exposures of O3 (ozone) and SOCl2 (thionyl chloride). In situ quartz crystal microbalance (QCM) studies were performed on sputtered Mo-coated QCM crystals. The QCM results revealed that Mo ALE displayed a linear mass decrease versus ALE cycles after a short etching delay. A pronounced mass increase was observed for every O3 exposure. A dramatic mass decrease occurred for every SOCl2 exposure. The mass change per cycle (MCPC) for Mo ALE was self-limiting after long SOCl2 exposures. The MCPC increased slightly with longer O3 exposure times. In situ QCM studies suggested that this soft saturation with longer exposure to the O3 resulted from the diffusion-limited oxidation of Mo. The Mo etch rate increased progressively with etching temperature. Under saturation conditions, the Mo etch rates were 0.94, 5.77, 8.83, and 10.98 Å/cycle, at 75, 125, 175, and 225 °C, respectively. X-ray photoelectron spectroscopy (XPS) and in situ quadruple mass spectroscopy (QMS) studies were conducted to understand the reaction mechanism. XPS revealed primarily MoO3 on the Mo surface after exposure to O3 at 150 °C. From the QMS studies, volatile SO2 and MoO2Cl2 were monitored when Mo was exposed to SOCl2 during the ALE cycles at 200 °C. These results indicate that Mo ALE occurs via oxidation and deoxychlorination reactions. Mo is oxidized to MoO3 by O3. Subsequently, MoO3 undergoes a deoxychlorination reaction where SOCl2 accepts oxygen to yield SO2 and donates chlorine to produce MoO2Cl2. Additional QCM experiments revealed that sequential exposures of O3 and SO2Cl2 (sulfuryl chloride) did not etch Mo at 250 °C. Time-resolved QMS studies at 200 °C also compared sequential O3 and SOCl2 or SO2Cl2 exposures on Mo at 200 °C. The volatile release of MoO2Cl2 was observed only using the SOCl2 deoxychlorination reactant. Atomic force microscopy (AFM) measurements revealed that the roughness of the Mo surface increased slowly versus Mo ALE cycles.

Rapid preparation of large size, few-layered MoO 3 by anisotropic etching

Controllable preparation of monolayer MoO3/MoO by using plasma oxidation and atomic layer etching

Electrochemically Exfoliating MoS 2 into Atomically Thin Planar‐Stacking Through a Selective Lateral Reaction Pathway

Thermal Atomic Layer Etching of Molybdenum Using Sequential Oxidation and Deoxychlorination Reactions

Facile preparation of anodized MoO3−x films and their boosted photocatalytic activity

Low-temperature Exfoliation of Multilayer-Graphene Material from FeCl3 and CH3NO2 Co-Intercalated Graphite Compound.

Facile Exfoliation for High-Quality Molybdenum Disulfide Nanoflakes and Relevant Field-Effect Transistors Developed With Thermal Treatment

Direct Exfoliation Of Natural Sio2-Containing Molybdenite In Isopropanol: A Cost Efficient Solution For Large-Scale Production Of Mos2 Nanosheetes

Exfoliation of Metal–Organic Frameworks to Give 2D MOF Nanosheets for the Electrocatalytic Oxygen Evolution Reaction

Wafer-Scalable Single-Layer Amorphous Molybdenum Trioxide

Preparation and Growth Mechanism of Molybdenum Trioxide Whisker

Aqueous and mechanical exfoliation, unique properties, and theoretical understanding of MoO3 nanosheets made from free-standing α-MoO3 crystals: Raman mode softening and absorption edge blue shift

Synthesis of Nanometre-Thick MoO3 Sheets.

Controlled Intercalation and Chemical Exfoliation of Layered Metal-Organic Frameworks Using A Chemically Labile Intercalating Agent

Solvent-assisted exfoliation for high-quality molybdenum disulfide nanoflakes and relevant field-effect transistors

Van Der Waals Epitaxy of Ultrathin Α-Moo3 Sheets on Mica Substrate with Single-Unit-cell Thickness

Facile Preparation of Few-layer MoS2-NS by Liquid-Phase Ultrasonic Exfoliation

Rapid synthesis of MoS2 for transistors and memristors

Exploration of New Self-limiting Atomic Layer Etching Methods for Molybdenum

Synthesis And Fast Transfer Of Monolayer Mos2 On Reusable Fused Silica

Exfoliation of Large-Flake, Few-Layer MoS2 Nanosheets Mediated by Carbon Nanotubes.