Abstract:Magnesium alloys are ideal lightweight materials; however, their applications are extremely limited due to their low strength, poor ductility, and weak corrosion resistance. In the present study, a friction stir processing (FSP) treatment was employed to optimize the mechanical properties and corrosion resistance of an as-cast Mg-5Zn alloy. The average grain size of the Mg-5Zn alloy was refined from 133.8 & mu;m to 1.3 & mu;m as a result of FSP. Along different directions, FSP exhibited the enhancement effects on different mechanical properties. Furthermore, according to the potentiodynamic polarization results, the corrosion current density at the free-corrosion potential of the FSPed sample, was 4.1 x 10 -6 A/cm 2 in 3.5 wt.% NaCl aqueous solution, which was significantly lower than that of the as-cast sample. Electrochemical impedance spectroscopy revealed that the polarization impedance, R p , of the FSPed sample was 1534 S2/cm 2 in 3.5 wt.% NaCl aqueous solution, which was 71.4% greater than that of the as-cast sample. The corrosion morphology of the FSPed sample in 3.5 wt.% NaCl aqueous solution exhibited largely uniform corrosion, rather than severe localized corrosion characteristics, which further reduced the corrosion depth on the basis of reducing the corrosion current density. The results presented herein indicate that FSP is a viable technique for simultaneously improving the mechanical properties and corrosion resistance of the as-cast Mg-5Zn alloy. & COPY; 2022 Chongqing University. Publishing services provided by Elsevier B.V. on behalf of KeAi Communications Co. Ltd. This is an open access article under the CC BY-NC-ND license ( http://creativecommons.org/licenses/by-nc-nd/4.0/ ) Peer review under responsibility of Chongqing University

Strengthening and toughening mechanisms of CNTs/Mg-6Zn composites via friction stir processing

Fabrication of metal matrix composites via friction stir processing

Microstructure and mechanical properties of carbon nano-onions reinforced Mg-based metal matrix composite prepared by friction-stir processing

Toughening and strengthening of Cu-coated carbon nanotubes reinforced AZ61 magnesium matrix nanocomposites by improving interfacial bonding

Developing Fittingly Comprehensive Performance Carbon Nanotube/Mg-6Zn Sheets with Substantial Enhancement in Formability

Microstructure evolution and mechanical properties of CNT/Al composite joints via friction stir welding

Fabrication of Graphite-Reinforced 6201al Matrix Composite with Simultaneous Enhancement of Mechanical and Electrical Properties by Multi-Pass Friction Stir Processing

Strengthening and toughening mechanisms of CNTs/Mg–Al composites prepared via powder metallurgy combined with hot extrusion

Effects of Energy Input During Friction Stir Processing on Microstructures and Mechanical Properties of Aluminum/carbon Nanotubes Nanocomposites

Strengthening Ni-Coated CNT/Mg Composites by Optimizing the CNT Content

Mechanical properties and fabrication of carbon nanotubes reinforced AZ91D magnesium matrix nanocomposites

Investigation of Microstructure and Strengthening Mechanism in CNTs Reinforced Mo-based Composites

Enhanced ductility with significant increase in strength of as cast CNTs/AZ91D nanocomposites

Effect of friction stir processing on the corrosion behavior of an Mg-Zn-Ca composite containing 1.0 wt% MgO

Simultaneous enhancement of mechanical properties and corrosion resistance of as-cast Mg-5Zn via microstructural modification by friction stir processing

Fabrication of in Situ Carbon Fiber/aluminum Composites Via Friction Stir Processing: Evaluation of Microstructural, Mechanical and Tribological Behaviors

Strengthening and Toughening Mechanisms of Mg Matrix Composites Reinforced with Specific Spatial Arrangement of In-Situ TiB2 Nanoparticles

Microstructure and Mechanical Property of Nano-Sicp Reinforced High Strength Mg Bulk Composites Produced by Friction Stir Processing

Enrichment in Fracture Ductility Tribological Characteristics of Magnesium-Based Nanocomposites Fabricated via Multi-pass Friction Stir Processing and Study of Significant Parameters

Synergistic toughening on CFRP via in-depth stitched CNTs

Enhancement of ultimate tensile strength and ductility of copper matrix composites using a low content of single-wall carbon nanotubes