Abstract:Selective laser melting (SLM) of aluminium alloys is of research interest due to its potential benefits in fabricating complex components for aerospace and automotive industries. In order to improve the mechanical properties and demonstrate the credibility of selective laser melted (SLMed) Al alloys, the effects of post heat treatment on the microstructures and mechanical properties need to be studies. In the present work, the nano-TiB2 decorated Al–7Si–Cu–Mg samples were successfully fabricated using the SLM technique, and then post-treated by direct ageing and conventional T6 heat treatment. The as-built TiB2/Al–7Si–Cu–Mg sample exhibits fine equiaxed grain structures without preferred crystallographic texture due to the high cooling rate of SLM and the addition of nano-TiB2 particles. Nano-scale eutectic Si cells are present within the equiaxed grains. Inside the cells, there are dislocation tangles without precipitates. After direct ageing treatment, the grain and cell structures remain almost unchanged, and the new Al2Cu, Mg2Si, and Si phases are formed around the dislocations. While after T6 treatment, the fine grains grow up and the eutectic Si phases coarse leading to the broken of cell structures. Besides, the as-built TiB2/Al–7Si–Cu–Mg samples show high tensile strength and ductility (yield strength: 297.2 MPa, ultimate tensile strength: 474.6 MPa, elongation: 13.4%). During ageing, the yield strength is enhanced by ~35% due to precipitation hardening effect. While the broken of fine microstructure during T6 leads to the decrease of yield strength by ~16%. The microstructure development and preliminary strengthening mechanism were discussed. The effect of post-heat treatments can yield the SLMed TiB2/Al–7Si–Cu–Mg samples with appropriate mechanical properties, promoting a wide range of applications.

Enhanced Micro-Hardness and Wear Resistance of Al-15Si/TiC Fabricated by Selective Laser Melting

Microstructure, solidification behavior and mechanical properties of Al-Si-Mg-Ti/TiC fabricated by selective laser melting

Microstructure and Mechanical Behavior of TiCN Reinforced AlSi10Mg Composite Fabricated by Selective Laser Melting

Microstructure evolution and mechanical properties of selective laser melting fabricated hybrid particle reinforced AlSi10Mg composites

Microstructural Characteristics And Elevated Temperature Wear Of Ti-11si-16al Alloy

Study of the microstructure and wear properties of Ti-12Mo-6Zr-2Fe alloy fabricated via selective laser melting

Microstructure and Mechanical Property of Ti–5Al–5Mo–5V–3Cr–1Zr Alloy Fabricated by Selective Laser Melting with a Preheated Substrate

Effects of Laser Processing Parameters on Microstructure and Mechanical Properties of Additively Manufactured AlSi10Mg Alloys Reinforced by TiC

Effects of Micron/Submicron TiC on Additively Manufactured AlSi10Mg: A Comprehensive Study from Computer Simulation to Mechanical and Microstructural Analysis

Enhancing Hardness and Wear Performance of Laser Additive Manufactured Ti6Al4V Alloy Through Achieving Ultrafine Microstructure

Effect of the Addition of Cu and Al on the Microstructure, Phase Composition and Properties of a Ti-6Al-4V Alloy Obtained by Selective Laser Melting

Nano-SiC whisker-reinforced Ti6Al4V matrix composites manufactured by selective laser melting: fine equiaxed grain formation mechanism and mechanical properties

In situ formation of D022-Al3Ti during selective laser melting of nano-TiC/AlSi10Mg alloy prepared by electrostatic self-assembly

Microstructure and Properties of TiC/AlMgSc Composites by Selective Laser Melting

Selective Laser Melting of Nano-Tib2 Decorated Alsi10mg Alloy with High Fracture Strength and Ductility

Microstructure, heat treatment and mechanical properties of TiB2/Al–7Si–Cu–Mg alloy fabricated by selective laser melting

Effect of Ti microalloying and laser remelting on the microstructure and mechanical properties of laser powder bed fusion Al-12Si alloy

The Wear Behavior of the Laser Cladded Ti-Al-Si Composite Coatings on Ti-6Al-4V Alloy with Additional TiC

Wear Behavior of a Heat-Treatable Al-3.5Cu-1.5Mg-1Si Alloy Manufactured by Selective Laser Melting

Interfacial structures and strengthening mechanisms of in situ synthesized TiC reinforced Ti6Al4V composites by selective laser melting

High-strength and thermally stable TiB2-modified Al–Mn–Mg–Er–Zr alloy fabricated via selective laser melting