Abstract:Selective laser melting (SLM), due to its track-by-track and layer by layer localized additive manufacturing process nature, has significant requirements for the optimization of laser scanning strategy and parameter. In this work, rare earth element Sc- and Zr- modified Al-Mg alloy was processed by SLM using an "island" scanning strategy with different island sizes. The influence of island size on surface quality, microstructural feature, residual stress, tensile property and corrosion resistance of SLM-processed Al-Mg-Sc-Zr alloy was systematically investigated. Experimental results indicated that the surface smoothness was enhanced as the island size decreased, but the influence of island size on microstructural development and tensile properties was not distinct. Considerably high tensile properties above 500 MPa combined with elongations of 10%-12% were generally obtained for Al-Mg-Sc-Zr specimens processed under different island sizes. Minimum residual stress was generated at a moderate island size of 2.4 mm and the residual stress increased both at a small and a large island size. A similar tendency was also observed for the corrosion resistance of SLM processed Al-Mg-Sc-Zr specimens, where a superior corrosion resistance (i(corr) = 6.82 x 10(-6) A cm(-2)) was generated at the middle island size. The different temperature gradient and thermal behaviors under different island sizes contribute to the variation of surface conditions and residual stresses. The change in corrosion behaviors under different island sizes was related to the different molten pool configurations. These findings provided the knowledge of the relationship between laser scanning strategy and properties of SLM processed Al-Mg-Sc-Zr alloy, which further facilitated process optimization and engineering applications of laser additive manufacturing of high-performance Al-Mg-Sc-Zr alloy.

Comparisons on Microstructure, Mechanical and Corrosion Resistant Property of S136 Mold Steel Processed by Selective Laser Melting from Two Pre-Alloy Powders with Trace Element Differences

Relative Density of Mold Steel H13 Fabricated by Hybrid Laser Spot Melting

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Selective laser melting of maraging steel: mechanical properties development and its application in mold

Effect of laser power on microstructures and properties of Al-4.82Mg-0.75Sc-0.49Mn-0.28Zr alloy fabricated by selective laser melting

Selective Laser Melting of P20 Mould Steel: Investigation on the Resultant Microstructure, High-Temperature Hardness and Corrosion Resistance

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

The mechanical properties and corrosion resistance of selective laser melting 30CrMnSiA steel

Improved Corrosion Behavior of Ultrafine-Grained Eutectic Al-12Si Alloy Produced by Selective Laser Melting

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Influence of Scanning Strategy and Parameter on Microstructural Feature, Residual Stress and Performance of Sc and Zr Modified Al–Mg Alloy Produced by Selective Laser Melting

Microstructure and mechanical properties of Al-Fe-Sc-Zr alloy additively manufactured by selective laser melting

Fabrication and Characterization of AISI 420 Stainless Steel Using Selective Laser Melting

Cracking Behavior, Microstructure and Properties of Selective Laser Melted Al-Mn-Mg-Sc-Zr Alloy

Densification, Microstructure and Mechanical Properties of an Al-14.1Mg-0.47Si-0.31Sc-0.17Zr Alloy Printed by Selective Laser Melting

Comparison of AlSi7Mg0.6 alloy obtained by selective laser melting and investment casting processes: Microstructure and mechanical properties in as-built/as-cast and heat-treated conditions

Microstructure and Mechanical Properties of a Novel Sc and Zr Modified 7075 Aluminum Alloy Prepared by Selective Laser Melting

Process parameter optimization and mechanical properties for selective laser melting of AlSi10Mg alloy

Microstructures and mechanical properties of Si and Zr modified Al–Zn–Mg–Cu alloy-A comparison between selective laser melting and spark plasma sintering

Influence of Selective Laser Melting Process Parameters on Microstructure and Properties of a Typical Ni-Based Superalloy

Microstructure evolution during selective laser melting of metallic materials: A review