Abstract:Traditional high-speed electrolyte flow for removing bubbles and sludges from the inter-electrode gap during electrochemical machining (ECM) usually results in the non-uniform distribution of temperature, bubbles, and sludges, thus deteriorating machining accuracy. Therefore, ECM performed in stationary electrolyte via an efficient flushing method may solve this problem. For this reason, the previous study proposed the stamp flushing method to squeeze out the bubbles and sludge from the inter-electrode gap by shortening the gap width. However, the effectiveness of the stamp flushing method in achieving high replicability has not been systematically investigated. In the present work, the stamp stroke motion was first optimized to improve the flushing efficiency of the stamp flushing method. To obtain higher stamping velocity and to avoid the damage due to the collision between the tool electrode and workpiece, a cushion mechanism was newly installed on the equipment. Based on the optimized stamp stroke motion, the periodical micropatterns fabricated on the tool electrode surface using wire electrical discharge machining (WEDM) were replicated onto the SK4 workpiece using ECM in stationary electrolyte. The dimensional deviation of the workpiece from the tool electrode after ECM was less than 4 mu m in the feed direction and approximately 30 mu m in the side direction when the initial width of the frontal gap was 10 mu m. Outside the inter-electrode gap, the electrolyte flowing along the axial direction (EFAAD) was supplied to rapidly flush out the bubbles and sludge squeezed out by stamp motion to prevent them from backflowing into the inter-electrode gap during the widening phase of the gap after the stamp motion. Since the EFAAD does not affect the electrolyte in the inter-electrode gap, the ECM remains performed in a stationary electrolyte. High replicability was obtained uniformly over the working surface, which originates from the combined effect of small inter-electrode gap width and uniform distribution of temperature, bubbles, and sludge in stationary electrolyte. This work proves the potential of the proposed stamp-flushing method for manufacturing metal parts with high replicability.

Self-adjusting EDM/ECM High Speed Drilling of Film Cooling Holes

Effects of Dielectric Fluids on Surface Integrity for the Recast Layer in High Speed EDM Drilling of Nickel Alloy

Improvement of machining accuracy in EDCM by enhanced electrochemical reaming based on a non-metallic backing layer

Performance improvement of high-speed EDM and ECM combined process by using a helical tube electrode with matched internal and external flushing

Study on the Evolution Process of Recast Layer for Fast EDM Drilling Based on Observation Experiment and a Novel Thermal-Fluid Coupling Model

Thinning Process Of Recast Layer In Hole Drilling And Trimming By Edm

Development of EDM Equipment for Machining Film Cooling Holes

Insights into the high-speed electrochemical discharge drilling for film cooling hole: Machining phenomena, morphological evolution, and visualize simulation

Vibration-assisted electrochemical discharge drilling method for microholes without recast layer

Improving surface integrity of micro-holes in ECDM using ultrahigh-speed rotary of tool cathode and non-water-based electrolyte

Experimental investigation of the EDM tools coated with nano-alumina film

Electrochemical discharge machining grooves without recast layer in 20 wt% NaCl solution

Achieving High Replicability for Electrochemical Machining Via the Stamp Flushing Method in Stationary Electrolyte

Process Parameters Optimization of Film Cooling Holes and Measurement Experiment of Recast Layer Thickness in EDM

Investigation of the Material Removal Mechanism in Electrochemical Discharge Drilling Using a High-Speed Rotating Helical Tool-Electrode

High-speed Electrochemical Discharge Drilling (HSECDD) for Micro-Holes on C17200 Beryllium Copper Alloy in Deionized Water

A Sustainable Machining Method with High Efficiency, High Quality and Low Wear - Electric Arc Electrochemical Composite Machining

Adaptive planetary control with auxiliary magnetic field method for fast EDM drilling

High-speed Near Dry Electrical Discharge Machining

Surface integrity of holes machined by electrochemical discharge drilling method

Study on material removal mechanism and control strategy of multi-axis fast ED-milling