Abstract:2D field-effect transistors (FETs) fabricated with transition metal dichalcogenide (TMD) materials are a potential replacement for the silicon-based CMOS. However, the lack of advancement in p-type contact is also a key factor hindering TMD-based CMOS applications. The less investigated path towards improving electrical characteristics based on contact geometries with low contact resistance (RC) has also been established. Moreover, finding contact metals to reduce the RC is indeed one of the significant challenges in achieving the above goal. Our research provides the first comparative analysis of the three contact configurations for a WSe2 monolayer with different noble metals (Rh, Ru, and Pd) by employing ab initio density functional theory (DFT) and non-equilibrium Green's function (NEGF) methods. From the perspective of the contact topologies, the RC and minimum subthreshold slope (SSMIN) of all the conventional edge contacts are outperformed by the novel non-van der Waals (vdW) sandwich contacts. These non-vdW sandwich contacts reveal that their RC values are below 50 Ω∙μm, attributed to the narrow Schottky barrier widths (SBWs) and low Schottky barrier heights (SBHs). Not only are the RC values dramatically reduced by such novel contacts, but the SSMIN values are lower than 68 mV/dec. The new proposal offers the lowest RC and SSMIN, irrespective of the contact metals. Further considering the metal leads, the WSe2/Rh FETs based on the non-vdW sandwich contacts show a meager RC value of 33 Ω∙μm and an exceptional SSMIN of 63 mV/dec. The two calculated results present the smallest-ever values reported in our study, indicating that the non-vdW sandwich contacts with Rh leads can attain the best-case scenario. In contrast, the symmetric convex edge contacts with Pd leads cause the worst-case degradation, yielding an RC value of 213 Ω∙μm and an SSMIN value of 95 mV/dec. While all the WSe2/Ru FETs exhibit medium performances, the minimal shift in the transfer curves is interestingly advantageous to the circuit operation. Conclusively, the low-RC performances and the desirable SSMIN values are a combination of the contact geometries and metal leads. This innovation, achieved through noble metal leads in conjunction with the novel contact configurations, paves the way for a TMD-based CMOS with ultra-low RC and rapid switching speeds.

Selecting Electrode Materials for Monolayer ReS2 with an Ohmic Contact

Strain-engineering the Anisotropic Electrical Conductance in ReS2 Monolayer

Electronic and Optoelectronic Applications Based on ReS2

Monolayer SnS2 Schottky barrier field effect transistors: effects of electrodes

Efficient Ohmic Contact in Monolayer CrX2N4 (X = C, Si) Based Field‐Effect Transistors

Designing high-efficiency electrode contacts to two-dimensional semiconductor Cu 2 Se

Ohmic MXene Contacts for Symmetric P- and N-Type Monolayer WSe2 Schottky Barrier Field-Effect Transistors

The Contacts of the Monolayer Semiconductor C2N with 2D Metal Electrodes

Synthesis of high-crystalline ReS2 monolayers by sodium-assisted chemical vapor deposition

Synthesis of high-crystalline ReS<sub>2</sub> monolayers by sodium-assisted chemical vapor deposition

Achieving nearly barrier free transport in high mobility ReS 2 phototransistors with van der Waals contacts

Reexamination of the Schottky Barrier Heights in Monolayer MoS2 Field-Effect Transistors

Ohmic Contacts Between Monolayer WSe2 and Two-Dimensional Titanium Carbides

Planar Direction‐Dependent Interfacial Properties in Monolayer In2Se3–Metal Contacts

Unusual Fermi‐Level Pinning and Ohmic Contact at Monolayer Bi2O2Se–Metal Interface

Doping‐Induced Performance Improvement in ReS2 Field Effect Transistors: Exploring a Heterostructure with In2O3 Quantum Dots

Deeply Exploring Anisotropic Evolution Toward Large-Scale Growth of Monolayer ReS2.

Impact of Rh, Ru, and Pd Leads and Contact Topologies on Performance of WSe2 FETs: A First Comparative Ab Initio Study

ReS2‐Based Field‐Effect Transistors and Photodetectors

Monolayer behaviour in bulk ReS 2 due to electronic and vibrational decoupling

Junction-configuration-dependent interfacial electronic states of a monolayer MoS2/metal contact