Abstract:Ultrasound-assisted grinding is a new method for compound precision machining of C/SiC with excellent machining characteristics. The electroplated diamond grinding head performs a two-dimensional ultrasonic auxiliary plane grinding single-factor experiment for SiC, 2.5D-C/SiC, and chopped fiber-C/SiC. The influences of linear speed, feed speed, grinding depth, fiber orientation, and fiber structure on the grinding force and surface quality are analyzed in this study. The surface formation and removal mechanisms of C/SiC composites are discussed. The results show that within the parameters of this experiment, the grinding force and surface roughness decrease with the increase in linear speed and increase with the increase in feed speed and grinding depth. The grinding force and roughness can be significantly reduced by applying two-dimensional ultrasound. The maximum percentage reduction in normal and tangential grinding forces was 26.79% and 31.69% when grinding 2.5D-C/SiC along 90° fiber orientation. The maximum percentage of surface roughness reduction was 37.93% when 2.5D-C/SiC was ground along a 90° fiber orientation. The influence of fiber orientation on the two types of C/SiC grinding force is the same, and both are satisfied that the grinding force is highest in the 45° fiber orientation, second highest in the 90° fiber orientation, and lowest in the 0° fiber orientation. The effect of fiber orientation on the roughness of 2.5D-C/SiC is as follows: the surface roughness is highest at 45° fiber orientation, second highest at 90° fiber orientation, and lowest at 0° fiber orientation. The effect of fiber orientation on the roughness of short-cut fiber-C/SiC is as follows: the surface roughness is highest at 0° fiber orientation, second highest at 45° fiber orientation, and lowest at 90° fiber orientation. The effect of fiber structure on grinding force is as follows: Under the same machining conditions, the grinding forces are highest on SiC, second highest on short-cut fiber-C/SiC, and lowest on 2.5D-C/SiC. The effect of fiber structure on surface roughness is as follows: Under the same machining conditions, the surface roughness is highest on short-cut fiber-C/SiC, second highest on 2.5D-C/SiC, and lowest on SiC.

Surface Topography and Roughness of Silicon Carbide Ceramic Matrix Composites

Some observations in grinding surface quality of FRCMC

Some Observations in Grinding SiC and Silicon Carbide Ceramic Matrix Composite Material

Effect of Ultrasonic Vibration Assisted Grinding Process on Surface Topography and Properties of C/SiC Composite

A Study on 3D Micro-Topographical Measurement of FRCMC Grinding Surface

An Experimental Investigation on Ultrasonic Vibration-Assisted Grinding of SiO2f/SiO2Composites

A Study on Grinding Surface Waviness of Woven Ceramic Matrix Composites

Grinding Characteristics and Removal Mechanism of 2.5D-Needled Cf/SiC Composites

Assessment of Machined Surface for SiCf/SiC Ceramic Matrix Composite During Ultrasonic Vibration-Assisted Milling-Grinding

Research of the Grinding Force and Surface Morphology of Fiber-Reinforced Ceramic Matrix Composite

Grinding characteristics and removal mechanisms of unidirectional carbon fibre reinforced silicon carbide ceramic matrix composites

Grinding Characteristics and Surface Roughness Modeling of 2.5D Woven SiCf/SiC Ceramic Matrix Composites

Research on micro-grinding performance of 2.5D Cf/SiC composites

Wear-induced variation of surface roughness in grinding 2.5D C f /SiC composites

Study on removal mechanism and surface quality of grinding carbon fiber toughened ceramic matrix composite

Experimental Investigation on Evaluation Method of Milling-grinding Surface Quality for SiC<sub>f</sub>/SiC Composite

Experimental study of the removal characteristics of C/SiC with different fiber structure arrangements for two-dimensional ultrasound-assisted grinding

Surface Grinding of C/C Composite Material

Study of Material Removal Mechanisms in Grinding of C/SiC Composites Via Single-Abrasive Scratch Tests

Influence of the fiber orientation on 3D C/C–SiC composite material and its formation mechanism of the machining surface

Mechanical Model and Removal Mechanism of Unidirectional Carbon Fibre-Reinforced Ceramic Composites