Abstract:Ultrasound-assisted grinding is a new method for compound precision machining of C/SiC with excellent machining characteristics. The electroplated diamond grinding head performs a two-dimensional ultrasonic auxiliary plane grinding single-factor experiment for SiC, 2.5D-C/SiC, and chopped fiber-C/SiC. The influences of linear speed, feed speed, grinding depth, fiber orientation, and fiber structure on the grinding force and surface quality are analyzed in this study. The surface formation and removal mechanisms of C/SiC composites are discussed. The results show that within the parameters of this experiment, the grinding force and surface roughness decrease with the increase in linear speed and increase with the increase in feed speed and grinding depth. The grinding force and roughness can be significantly reduced by applying two-dimensional ultrasound. The maximum percentage reduction in normal and tangential grinding forces was 26.79% and 31.69% when grinding 2.5D-C/SiC along 90° fiber orientation. The maximum percentage of surface roughness reduction was 37.93% when 2.5D-C/SiC was ground along a 90° fiber orientation. The influence of fiber orientation on the two types of C/SiC grinding force is the same, and both are satisfied that the grinding force is highest in the 45° fiber orientation, second highest in the 90° fiber orientation, and lowest in the 0° fiber orientation. The effect of fiber orientation on the roughness of 2.5D-C/SiC is as follows: the surface roughness is highest at 45° fiber orientation, second highest at 90° fiber orientation, and lowest at 0° fiber orientation. The effect of fiber orientation on the roughness of short-cut fiber-C/SiC is as follows: the surface roughness is highest at 0° fiber orientation, second highest at 45° fiber orientation, and lowest at 90° fiber orientation. The effect of fiber structure on grinding force is as follows: Under the same machining conditions, the grinding forces are highest on SiC, second highest on short-cut fiber-C/SiC, and lowest on 2.5D-C/SiC. The effect of fiber structure on surface roughness is as follows: Under the same machining conditions, the surface roughness is highest on short-cut fiber-C/SiC, second highest on 2.5D-C/SiC, and lowest on SiC.

New Observations of the Fiber Orientations Effect on Machinability in Grinding of C/SiC Ceramic Matrix Composite

Investigations on Grinding Process of Woven Ceramic Matrix Composite Based on Reinforced Fiber Orientations

Some observations in grinding surface quality of FRCMC

Research of the Grinding Force and Surface Morphology of Fiber-Reinforced Ceramic Matrix Composite

A Study on Grinding Surface Waviness of Woven Ceramic Matrix Composites

Influence of the fiber orientation on 3D C/C–SiC composite material and its formation mechanism of the machining surface

Experimental investigation on grinding-induced surface damage of Fiber Reinforced Ceramic Matrix Composites

Effect of fiber orientation on material removal mechanisms in the machining of 3D Cf/SiC composite with a brazed diamond grinding rod: Experiment and simulation

A Force Model in Single Grain Grinding of Long Fiber Reinforced Woven Composite

Experimental study of the removal characteristics of C/SiC with different fiber structure arrangements for two-dimensional ultrasound-assisted grinding

Analysis on Ground Surface Damage of Quartz Fiber-Reinforced Quartz Composites

An Experimental Investigation on Ultrasonic Vibration-Assisted Grinding of SiO2f/SiO2Composites

Fiber Orientations Effect on Process Performance for Wire Cut Electrical Discharge Machining (WEDM) of 2D C/SiC Composite

Study on removal mechanism and surface quality of grinding carbon fiber toughened ceramic matrix composite

Investigation on the Effects of Microstructure on Machining Unidirectional Carbon Fiber Reinforced Polymer Composites with a Modified Force Model

Grinding Characteristics and Surface Roughness Modeling of 2.5D Woven SiCf/SiC Ceramic Matrix Composites

Effect of machining parameters on the milling process of 2.5D C/SiC ceramic matrix composites

Investigation on machined surface quality in ultrasonic-assisted grinding of Cf/SiC composites based on fracture mechanism of carbon fibers

Diamond wheel grinding characteristics of 3D orthogonal quartz fiber reinforced silica ceramic matrix composite

Effects of Meso-Structure in Grinding of 2.5D Woven Fiber-Reinforced Ceramic Composites

Study on Removal Mechanism and Surface Quality of SiCf/SiC Composites by Longitudinal Torsional Ultrasonic Vibration-Assisted Grinding