Abstract:Ultrasound-assisted grinding is a new method for compound precision machining of C/SiC with excellent machining characteristics. The electroplated diamond grinding head performs a two-dimensional ultrasonic auxiliary plane grinding single-factor experiment for SiC, 2.5D-C/SiC, and chopped fiber-C/SiC. The influences of linear speed, feed speed, grinding depth, fiber orientation, and fiber structure on the grinding force and surface quality are analyzed in this study. The surface formation and removal mechanisms of C/SiC composites are discussed. The results show that within the parameters of this experiment, the grinding force and surface roughness decrease with the increase in linear speed and increase with the increase in feed speed and grinding depth. The grinding force and roughness can be significantly reduced by applying two-dimensional ultrasound. The maximum percentage reduction in normal and tangential grinding forces was 26.79% and 31.69% when grinding 2.5D-C/SiC along 90° fiber orientation. The maximum percentage of surface roughness reduction was 37.93% when 2.5D-C/SiC was ground along a 90° fiber orientation. The influence of fiber orientation on the two types of C/SiC grinding force is the same, and both are satisfied that the grinding force is highest in the 45° fiber orientation, second highest in the 90° fiber orientation, and lowest in the 0° fiber orientation. The effect of fiber orientation on the roughness of 2.5D-C/SiC is as follows: the surface roughness is highest at 45° fiber orientation, second highest at 90° fiber orientation, and lowest at 0° fiber orientation. The effect of fiber orientation on the roughness of short-cut fiber-C/SiC is as follows: the surface roughness is highest at 0° fiber orientation, second highest at 45° fiber orientation, and lowest at 90° fiber orientation. The effect of fiber structure on grinding force is as follows: Under the same machining conditions, the grinding forces are highest on SiC, second highest on short-cut fiber-C/SiC, and lowest on 2.5D-C/SiC. The effect of fiber structure on surface roughness is as follows: Under the same machining conditions, the surface roughness is highest on short-cut fiber-C/SiC, second highest on 2.5D-C/SiC, and lowest on SiC.

Fiber Orientations Effect on Process Performance for Wire Cut Electrical Discharge Machining (WEDM) of 2D C/SiC Composite

Investigations on Grinding Process of Woven Ceramic Matrix Composite Based on Reinforced Fiber Orientations

New Observations of the Fiber Orientations Effect on Machinability in Grinding of C/SiC Ceramic Matrix Composite

Some observations in grinding surface quality of FRCMC

Effect of fiber orientation on material removal mechanisms in the machining of 3D Cf/SiC composite with a brazed diamond grinding rod: Experiment and simulation

Influence of the fiber orientation on 3D C/C–SiC composite material and its formation mechanism of the machining surface

Investigation on the Effects of Microstructure on Machining Unidirectional Carbon Fiber Reinforced Polymer Composites with a Modified Force Model

Machining characteristics of 65 vol.% SiCp/Al composite in micro-WEDM

Effects of Fiber Orientations on Removal Behaviors in Ultrasonic Vibration-Assisted Grinding Continuous Fiber Reinforced Ti Matrix Composite

Experimental study of the removal characteristics of C/SiC with different fiber structure arrangements for two-dimensional ultrasound-assisted grinding

A Unified Geometrical Modeling and Analysis Method for Evaluating CFRP Machining Performance: Cutting Geometry Space

Analysis and Optimization of the Machining Characteristics of High-Volume Content SiCp/Al Composite in Wire Electrical Discharge Machining

Effect of machining parameters on the milling process of 2.5D C/SiC ceramic matrix composites

Investigation of milling performance and removal process mechanism of 3D SiCf/C-SiC composites using brazed diamond tools

Investigation of the Thermophysical Simulation and Material Removal Mechanism of the High-Volume-Fraction SiCp/Al Composite in Wire Electrical Discharge Machining

Factor Analysis of Machining Parameters of Fiber-Reinforced Polymer Composites Based on Finite Element Simulation with Experimental Investigation

Study on removal mechanism and surface quality of grinding carbon fiber toughened ceramic matrix composite

Effect of short electric arc milling discharge machining on the processing performance of two-dimensional C/SiC composites

Effect of cooling and lubrication conditions on the variable angle milling of unidirectional CFRP with PCD Tools

Effects of tool vibration on fiber fracture in rotary ultrasonic machining of C/SiC ceramic matrix composites

Effect of Al7075 and Activated Carbon reinforced Composite on Optimizing WEDM Responses