Abstract:Silicon -based ultra -thin flat heat pipes (UFHPs) that can be integrated with semiconductor devices provide an opportunity for electronic thermal management. To meet the requirements of various operation states, the impacts of gravity on the liquid plug characteristics and heat transfer performance of an UFHP are investigated by a visualization experiment conducted at different incline angles. Condensate flows back through microgrooves under the capillary pressure and gravity under a low heating power (capillary flow stage), and then excess condensate flows back along the edges of the UFHP under a higher heating power (gravitational flow stage). Over a certain heating power ( Q >= 14 W), liquid plug fluctuations caused by vapor entrainment are observed with periodic dry -out at the evaporator under large incline angles ( alpha >= 60 degrees ), corresponding to temperature fluctuations. Intense fluctuations of the liquid plug enhance sensible heat transfer, although the liquid plug occupies the condenser area and impedes the vapor flow. Meanwhile, evaporation at the evaporator benefits from corner -film evaporation until a large area of dry -out occurs. Due to the increased gravity and buoyancy, a larger incline angle is conducive to thermal performance enhancement, but this effect becomes restricted as the heating power rises. At a cooling -water temperature of 20 degrees C and an incline angle of 90 degrees , the lowest thermal resistances of the UFHP yield a value of 1.14 degrees C/W at 4 W in the steady stage and a value of 1.22 degrees C/W at 18 W in the fluctuation stage, respectively. The heat transfer limit of UFHP with overfilling reaches 24 W, compared with the theoretical heat transfer capacity of 8.9 W at an incline angle of 90 degrees . Additionally, a higher cooling -water temperature is beneficial for the thermal performance in the capillary flow stage, but not in the gravitational flow stage and fluctuation stage. This study provides guidance for the operational design of silicon -based UFHP for electronic thermal management.

Optimization of Temperature Uniformity of a Serpentine Thin Film Heater by a Two-Dimensional Approach

Thermohydraulic Performance Optimization of Integrated Porous Pin Fins in Microchannel Heat Sink Using Shape Optimization Coupled with NSGA

Heat Transfer Capacity Optimization Design of Microgroove and Microcolumn in an Ultra-Thin Flat Heat Pipe

Corner Flow Characteristics in a Silicon-Based Ultra-Thin Flat-Grooved Heat Pipe with Double-End Cooling

Enhancing Plate-Fin Heat Exchanger Hydraulic Thermal Performance Through Air-Side Fin Optimization Based on Pseudo-3D Topology Optimization

Liquid Plug Characteristics and Heat Transfer Performance of a Silicon-Based Ultra-Thin Flat Heat Pipe at Different Incline Angles

Optimization of the Thermal Field of 8-Inch SiC Crystal Growth by PVT Method with “3 Separation Heater Method”

Thermal design aspects for improving temperature homogeneity of silicon wafer during thermal processing in microlithography

Impact of flow intermittency on heat transfer enhancement in serpentine channels

Heat transfer performance comparison of printed circuit heat exchangers with straight, zigzag and serpentine flow channels for waste heat recovery

Thermo-hydraulic performance of solar air heater with built-in one-eighth sphere vortex generators

Development of a Microheater with a Large Heating Area and Low Thermal Stress in the Heating Area

Turbulent flow-thermal-thermodynamic characteristics of a solar air heater with spiral fins

An efficient plate heater with uniform surface temperature engineered with effective thermal materials

Improvement of temperature uniformity of induction-heated T-shape susceptor for high-temperature MOVPE

Assessing the enhancements in thermal performance of two-phase thermosyphon loops through riser wettability optimization

Thermo-hydraulic characteristic investigation of a circular tube inserted with constructal bifurcation semi-pipes by numerical simulation and PIV experiments

Experimental investigation on air-cooling type loop thermosyphon thermal characteristic with serpentine tube heat exchanger

Enhancement mechanism on heat and mass transfer of tall fin with cycloid thermosyphon loop

Investigation of cooling performance of micro-channel structure embedded in LTCC substrate for 3D micro-system

Thermal performance promotion of a novel double-tube heat exchanger by helical fin with perforations