Abstract:Crack behavior of aluminum alloy 2A12-T4 is investigated experimentally and numerically using cruciform specimens subjected to in-plane biaxial loadings applied in horizontal (x axis) and vertical (y axis) directions. Different cruciform configuration plans, with variant sizes of slots in loading arms and different transitional fillet radius between adjacent arms, are analyzed by means of FEM to confirm a final specimen geometry with relative uniform stress distribution in its central area. The tests for fatigue crack growth behavior under cyclic biaxial sinusoidal loadings with phase differences of 0 degrees or 60 degrees between two orthogonal fatigue loads are conducted by using a biaxial fatigue test system. The biaxial load ratio, P-max(x)/P-max(y), varies from -0.5 to 1.0. Initial central cracks are inclining in angles of 0 degrees, 45 degrees and 60 degrees to x-axis. Crack growth path and lives are obtained. It is observed that the crack growth behavior under biaxial loading differs from that with only uniaxial loading. A widely accepted fatigue crack growth model, which combines Paris equation, maximum tangential stress (MTS) criterion and an equivalent stress intensity factor (SIF) proposed by Tanaka, is used for mixed mode-I/II crack subjected biaxial loading. The combined model is evaluated by the SIFs analysis based on analytical and numerical solution. The mixed mode SIFs are calculated based on finite element analysis with mesh updating. The simulated crack growth path and growth lives correlate well with the experiments in most cases. Both the experiments and the simulations demonstrate that the tensile load parallel to crack path behaves as the retarder to the crack growth, and the compressive load parallel to crack path behaves as the promoter to the crack growth. It is found that equivalent SIF used in the model overestimates the effect of mode II SIF on the fatigue crack growth rate by Paris equation. It is questionable to use the combined model for the cases with asynchronous biaxial loadings or those leading to crack surface contact.

Study of Anisotropic Crack Growth Behavior for Aluminum Alloy 7050-T7451

Fatigue Crack Growth of Alloy 7050-T7451 Plate in L-S Orientation

Physical essence of long fatigue crack growth behavior for aluminum-lithium alloy

Fatigue Crack Behaviors under Asynchronous Biaxial Loading

Characterization of Anisotropic Fracture Behavior of 7075-T6 Aluminum Alloy Sheet under Various Stress States

Dynamic tests and constitutive model for 7075-T6 aluminum alloy

In‐Situ Optical Microscopy Study on Plastic Zone Size Estimation of Aluminum Alloy 7075‐T6 under Cyclic Loading

Crack Initiation and Early Propagation Plane Orientation of 2A12-T4 Aluminum Alloy under Tension-Torsion Fatigue Loading Including Mean Tensile Stress

Experimental Studies on Mixed-Mode Dynamic Fracture Behaviour of Aluminium Alloy Plates with Narrow U-Notch

Small Crack Growth Behavior And Life Prediction Of 7075-T73 Forged Aluminum Alloy

Analysis of Fracture Criteria for 7050 Aluminum Alloy with Different Geometries Based on the Elastic Strain Energy Density

Crack Growth Patterns of Aluminum Tubular Specimens Subjected to Cyclic Tensile Loads

Investigation of small fatigue cracks—I. Plastic deformation associated with small fatigue cracks

Study on fatigue crack initiation and propagation of cast aluminum alloy A356

Investigation of Fatigue Growth Behavior of an Inclined Crack in Aluminum Alloy Plate

Strain Rate-Dependent Constitutive and Low Stress Triaxiality Fracture Behavior Investigation of 6005 Al Alloy

Anisotropic mechanical behavior prediction of aluminum alloy sheet based on an anisotropic GTN model: Modeling, simulation and experimental investigation

Investigation of Uniaxial Asymmetric High-Cycle Fatigue Failure Behavior of 7075-T651 Aluminum Alloy Sheet

Fatigue Crack Propagation Behavior of 2050 Aluminum Alloy

A Strain Rate Dependent Fracture Model of 7050 Aluminum Alloy

Fatigue Crack Growth Testing and Evaluation for Aluminum Alloys at Temperatures of 25°C and −70°C