Abstract:The Ni-Mn-based shape memory alloys as a promising candidate of elastocaloric material has been reported in many literatures, especially on bulk samples. The as-spun ribbon, which has a larger surface area and is more efficient for heat transfer, is rarely studied and hence of importance. In the present work, we succeeded in producing very long as-spun Ni-Fe-Mn-(Al, In) ribbons, with around 300 mm in length. The microstructure and mechanical properties of these as-spun ribbons were thoroughly investigated by scanning electron microscopy / electron backscattered diffraction (SEM/EBSD), nanoindentation and 3-points bending experiments. Through SEM/EBSD analyses, the microstructure and texture of the as-spun ribbons were studied. A gradient in microstructure exists along the thickness direction (TD) of the ribbon, which is induced by the temperature gradient during fast rate solidification, resulting in fine equiaxed grains along the surface contacted with the rotating wheel in melt spinning process and elongated grains, respectively. Both equiaxed and elongated grains possess a strong {001} fiber texture (<001>//TD). Nanoindentation analyses show little variation of hardness between the two different microstructures. The ductility index of both Ni-Fe-Mn-Al and Ni-Fe-Mn-In ribbons are within the range of intermetallic materials. The substitution of In by Al allows to increase very slightly the ductility index, which can reach 0.75. The fine equiaxed grains show better tensile resistance than the elongated grains in 3-points bending test. The substitution of In by Al improves the maximum bending strain by a factor of 3. The maximum strain for Ni-Fe-Mn-Al as-spun ribbons can reach 3 % before fracture. Fractography shows that the intergranular fracture is the main damage mechanism in these as-spun ribbons.

Metallurgical characterization of melt-spun ribbons of U-5.4 wt%Nb alloy

MICROSTRUCTURE OF AS-MELT SPUN Al-Cu-Mg-Fe-Ni ALLOY AND ITS VARIATION IN CONTINUOUS HEAT TREATMENT

Structure and Magnetic Properties of Melt-Spun (Nd0.625ni0.375)(85)al-15 Ribbons

Microstructure and Mechanical Properties of Unalloyed Molybdenum Fabricated Via Wire Arc Additive Manufacturing

Microstructure and correlated mechanical properties study of Ni-(Fe, Co)-Mn-(Al, In) as-spun ribbons

Effect of cooling rates on as-cast microstructures of U-5.4Nb alloys

The Magnetic and Microstructural Evolution of Ni45mn24ga23co4cu4 Heusler Alloy Ribbons

Structural, Magnetic, and Mössbauer Study on Nb and Heat Treatment of Fe-Si-B-P-Cu-Nb Ribbons

The Microstructure of As-Melt Spun Al–7%Si–0.3%Mg Alloy and Its Variation in Continuous Heat Treatment

Crystallization kinetics and magnetic properties of Fe 63.5Co10Si13.5B9Cu 1Nb3 nanocrystalline powder cores

Formation process, microstructure characterization, and evolution mechanism of adiabatic shear bands in U-5.7Nb alloy under dynamic deformation

The Anisotropy of Nanocomposite Nd9Fe84.5Nb0.5B6 Melt Spun Ribbons

Crystallization Kinetics of Co-Finemet Amorphous Alloys and Magnetic Properties of Nanocrystalline Powder Cores

Effects of severe plastic deformation on the microstructures, mechanical properties, and corrosion behavior of U-5.5Nb alloy

Effects of Ribbon Thickness on Structure and Soft Magnetic Properties of a High-Cu-Content FeBCuNb Nanocrystalline Alloy

Effect of V Substitution for Nb on the Crystallization Kinetics of FINEMET Amorphous Alloys

Differences in the Structure and Magnetic Properties Of(nd 0.75 Pr 0.25 ) 9.5 Fe 76 X 4 B 10.5 (x=nb, Zr) Ribbons by Conventional and Microwave-Assisted Annealing Treatment

Gradient Microstructure and Multiple Mechanical Properties of AlSi9Cu Alloy Ribbon Produced by Melt Spinning

Phase Composition, Microstructures and Magnetic Properties of Melt-Spun Nd1.2Fe10.5Mo1.5 Ribbons and Their Nitrides

Texture of nanocomposite Nd2Fe14B/alpha-Fe melt spun ribbons

Fabrication Technique of Wide Nb42Ni40Co18 Amorphous Alloy Ribbons with High Melting Temperature