Abstract:Metal supported solid oxide fuel cells (MS-SOFC) possess several advantages like good mechanical property, easy assembling, fast start-up and capability to maintain redox stable due to fuel leakage. However, it has been a critical challenge to deposit cathode on the metal supported cell in the oxidizing atmosphere, which is mainly limited by the low calcination temperature yielding vulnerable electrolyte-electrode interface. The cathodes prepared in the protecting atmosphere are also not satisfied, instead it will increase the complexity of the cell fabrication process. Lower down the cathode deposition temperature using aqueous infiltration has become one of the optimized methods for MS-SOFC. Also, we have proposed an alternative way for the fabrication of metal supported single cell with robust cathode through whole cell reduction. Here, we present results of both above two approaches for the fabrication of nano-structured cathodes in MS-SOFC. The cells in this study are based on Fe-Ni (1:1 in mol ratio) support, Fe-Ni/YSZ anode and YSZ electrolyte prepared through tape-casting, thermal isostatic pressing and co-firing. As illustrated in the following schematic configuration, La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF) cathodes were deposited in the porous YSZ layer of the pre-reduced Ni-Fe|Ni-Fe-YSZ||YSZ||P-YSZ substrate by infiltration and fired at the cell operation temperature around 700 oC. A-site deficiency of ~4-8% was introduced into LSCF cathode and was expected to enhance the sintering activity of LSCF nano particles at low calcination temperature and to enhance the cathode performance by the excess cobalt and iron oxide at LSCF surface. As in the second approach, Sr0.95Ti0.3Fe0.63Ni0.07O3-δ – Gd0.1Ce0.9O1.95 (STFNi-GDC) graded cathode will be screen printed on the NiO-Fe2O3|NiO-Fe2O3-YSZ||YSZ|GDC substrate and fired at high temperature in air as normal cathode preparation procedure. Then the whole cell will be reduced in H2-Ar to obtain Fe-Ni alloy support and reduced STFNi cathode with in-situ exsolved (Fe,Ni) alloy nano particles anchored in the oxide surface. During the cell test, the reduced STFNi-(Fe,Ni) will be re-oxidized in air, forming the surface decorated iron and cobalt oxide particles, which were presumably to be expected to increase the cathode performance through improvement of oxygen surface exchange coefficient. Figure 1

Optimization of Ni YSZ Anodes for Tubular SOFC by a Novel and Efficient Phase Inversion-Impregnation Approach

YSZ Thin Films Prepared by a Novel Powder Coating Process on Porous NiO-YSZ Cermet

Performance and Optimization of Ni/3 Mol% Y2O3-ZrO2 Anode Supported SOFC

Fabrication of Metal-Supported Tubular Solid Oxide Fuel Cell by Phase-Inversion Method and in Situ Reduction

Novel BaO-decorated carbon-tolerant Ni-YSZ anode fabricated by an efficient phase inversion-impregnation approach

Anodic polarization creates an electrocatalytically active Ni anode/electrolyte interface and mitigates the coarsening of Ni phase in SOFC

Stability of Ni-YSZ Anode for SOFCs in Methane Fuel: the Effects of Infiltrating La0.8Sr0.2FeO3-δand Gd-Doped CeO2Materials

A Novel Method to Purposely Modify the Anode/Electrolyte Interface in Solid Oxide Fuel Cells

An Anode-Supported Micro-Tubular Solid Oxide Fuel Cell with Redox Stable Composite Cathode

A robust tubular solid oxide fuel cell through bifunctional praseodymium oxide nanocatalyst infiltration

Preparation and Performance of Tri-layer Composite Anode Supported Fuel Cell

In-Situ Formation of Nano-Structured Cathode on Metal Supported SOFC

Improvement of Cathode–electrolyte Interfaces of Tubular Solid Oxide Fuel Cells by Fabricating Dense YSZ Electrolyte Membranes with Indented Surfaces

Nanoengineering electrode for yttria-stabilized zirconia-based symmetrical solid oxide fuel cells to achieve superior output performance

Performance Evolution of Ni-YSZ Anode-Supported SOFCs During Initial-Stage Operation

Robust Ni-based Anode Deposited with La0.6Sr0.4FeO3-δfor Direct Methane-Fueled SOFCs

Direct-Methane Solid Oxide Fuel Cells with Hierarchically Porous Ni-Based Anode Deposited with Nanocatalyst Layer

La0.6Sr0.4Co0.2Fe0.8O3-δ Nanoparticles Modified Ni-based Anode for Direct Methane-Fueled SOFCs

An anode-supported hollow fiber solid oxide fuel cell with (Pr0.5Nd0.5)0.7Sr0.3MnO3-δ-YSZ composite cathode

Tailoring the Microstructure of a Solid Oxide Fuel Cell Anode Support by Calcination and Milling of YSZ

Multilayered SOFC Anode Structure with Electroless Ni-YSZ for Enhancement of Cell Performance