Abstract:In-plane uniaxial tension of AZ31 magnesium alloy sheet with non-basal texture has been conducted in order to demonstrate the effects of loading direction on the microstructure evolution and mechanical properties at ambient temperature. Loading axes are chosen to be along five directions distributed between rolling direction (RD) and transverse direction (TD), allowing various activities in involved slip and twinning modes to take place. As for twinning modes, electron backscattered diffraction observations confirm that the contribution of \({{\{ 10\overline{1}1\} }}\) compression twinning is minimal to the plastic deformation of all deformed samples. By comparison, \({{\{ 10\overline{1}2\} }}\) extension twinning (ET) not only serves as an important carrier on sustaining and accommodating plastic strain but also contributes to the emergence of TD-component texture with the progression of plastic strain. In terms of slip modes, analysis on Schmid factor demonstrates that the increasing tilted angle between loading direction and RD of sheet is unfavorable to the activation of basal <a> slip, whereas it contributes to the activation of prismatic <a> slip. These observations consequently explain the increasing tendency of 0.2% proof yield stress. Moreover, the activations of basal <a> slip and \({{\{ 10\overline{1}2\} }}\) ET collectively contribute to the concentration of two tilted basal poles toward normal direction. With increasing angle between loading direction and RD, the activations of basal <a> slip and \({{\{ 10\overline{1}2\} }}\) ET are gradually weakened. This leads to a weakening tendency about concentration of two tilted basal poles, a generally increasing tendency about Lankford value (r-value) and a generally decreasing tendency about strain-hardening exponent (n-value).

Microstructure Evolution and Deformation Behaviors of AZ31 Mg Alloy with Different Grain Orientation During Uniaxial Compression

Deformation behavior and microstructure evolution of AZ31 Mg alloy during gradient thermal compression

Hot Deformation Behavior and Microstructural Evolution of Twin-Roll-Casting Mg Alloy during High-Temperature Compression

Effect of crystal orientation on the deformation behavior of the magnesium alloy AZ31 during plane strain compression

Effect of Temperature on Microstructure and Texture During Compression of Az31

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Dependence of Microstructure Evolution and Mechanical Properties on Loading Direction for AZ31 Magnesium Alloy Sheet with Non-basal Texture During In-Plane Uniaxial Tension

Influence of Grain Orientation on Twinning During Warm Compression of Wrought Mg–3Al–1Zn

Temperature Dependency on the Microscopic Mechanism in the Normal Direction of Wrought AZ31 Sheet under Dynamic Compressive Behavior

Deformation Behavior and Microstructure Evolution of AZ31 Mg Alloy by Forging–Bending Repeated Deformation with Multi-pass Lowered Temperature

Dynamic mechanical response and microstructural evolution of extruded Mg AZ31B plate over a wide range of strain rates

Preferential grain growth and textural evolution of AZ31B Mg alloy during annealing after isothermal compression at 400 °C

Effect of Final Rolling Speed on Microstructure and Performance of AZ31 Magnesium Alloy Sheet under Small Strain Condition

Research on deformation mechanism of AZ31 magnesium alloy during uniaxial compression

Microstructural Characteristics and Subsequent Soften Mechanical Response in Transverse Direction of Wrought AZ31 with Elevated Compression Temperature

The effects of orientation control via tension-compression on microstructural evolution and mechanical behavior of AZ31 Mg alloy sheet

Effect of Sample Orientation on Static Recrystallization of Az31 Magnesium Alloy

Deformation Microstructure and Characteristics of Cast-Rolling and Normal Rolling AZ31 Magnesium Alloy Sheets

Microstructure evolution and characterization of the adiabatic shear bands in AZ31 magnesium alloy

Mechanism of Plastic Deformation of As-Extruded AZ31 Mg Alloy during Uniaxial Compression

Microstructure and Deformation Behavior of Dual-Directional Extruded AZ31 Magnesium Alloy