Abstract:An in-situ reaction controlled non-solvent induced phase separation (RC-NIPS) method was developed to tailor the morphology of polyvinyl chloride (PVC)/styrene-maleic anhydride (SMA) grafting polyethylene glycol (PEG) (SMA-g-PEG) blend ultrafiltration (UF) membrane. Herein, PVC and SMA was dissolved in dimethylacetamide (DMAc) solvent to prepare a casting solution (16 wt.% polymer concentration) at 50 °C. Subsequently, PEG (20 kDa) as an additive and reactant was added to the casting solution at a mass ratio of PEG to the polymer 1/1 wt./wt. to enhance the hydrophilicity and mechanical elongation of the membrane. Results demonstrated that the casting solution with PVC/SMA = 3/1 wt./wt. was an entirely compatible system. The viscosity of the casting solution with adding PEG gradually increased from 692 mPa s to1880 mPa s at the initial stage and 4780 mPa s at 42 h, then rose sharply to 27,320 mPa s at 84 h. This behavior was ascribed to the esterification reaction between PEG and SMA, leading to pre-gelation and gelation of the system. Whereafter, SMA-g-PEG graft polymers were obtained. Meanwhile, the degree of grafting (DG) increased from 0.40% at 12 h of the reaction to 2.61% at 42 h. Afterwards, a phase inversion using water as coagulation was used to prepare PVC/SMA-g-PEG blend membrane after a certain time of the esterification reaction. It was found that the morphology of resultant membranes systematically changed from asymmetric structure with a dense top layer and finger-like sublayer at the initial stage to a dense layer with a fully sponge-like structure after 18–42 h reaction. The PVC/SMA-g-PEG membrane obtained after the reaction of 42 h demonstrated better hydrophilicity, high pure water permeance and excellent toughness due to the internal plasticization of water molecules. The membrane also exhibited a high BSA rejection (>95%) and fouling recovery rate (FRR) (85.9%). Our work provides some insights on tailoring the UF membrane structure and simultaneously enhancing permeability, antifouling performance and toughness.

Enhanced Permeation and Antifouling Performance of Polyvinyl Chloride (PVC) Blend Pluronic F127 Ultrafiltration Membrane by Using Salt Coagulation Bath (SCB)

Improved Antifouling Properties of Polyvinyl Chloride Blend Membranes by Novel Phosphate Based-Zwitterionic Polymer Additive

Preparation of Positively-Charged Blend PVC/PEI Ultrafiltration Membranes with Crosslink Structure for Dye/Salt Separation

Synthesis of PVC-b-PEG Copolymer and Its Modification Effect on PVC Microfiltration Membrane

Positively Charged PVC Ultrafiltration Membrane Via Micellar Enhanced Ultrafiltration for Removing Trace Heavy Metal Cations

Improved permeability and antifouling properties of polyvinyl chloride ultrafiltration membrane via blending sulfonated polysulfone

Optimal synthesis of high fouling-resistant PVC-based ultrafiltration membranes with tunable surface pore size distribution and ultralow water contact angle for the treatment of oily wastewater

Evaluation of an innovative polyvinyl chloride (PVC) ultrafiltration membrane for wastewater treatment

‘Green’ Fabrication of PVC UF Membranes with Robust Hydrophilicity and Improved Pore Uniformity

Carbon based Nanofillers Embedded Fouling Resistant Polyvinyl Chloride Nanocomposite Membranes for Oil-water Separation

Poly(vinyl chloride) (PVC) hollow fiber ultrafiltration membranes prepared from PVC/additives/solvent

Tailoring the micro-structure of PVC/SMA-g-PEG blend ultrafiltration membrane with simultaneously enhanced hydrophilicity and toughness by in situ reaction-controlled phase inversion

Improved PVDF Membrane Performance by Doping Extracellular Polymeric Substances of Activated Sludge

Study of poly(vinyl chloride)/polyether sulphone co-blend ultrafiltration membrane

In-situ Modification of PVC UF Membrane by SiO2 Sol in the Coagulation Bath During NIPS Process

Construction of a composite microporous polyethylene membrane with enhanced fouling resistance for water treatment

Structures and Antifouling Properties of Polyvinyl Chloride/poly(methyl Methacrylate)-Graft-poly(ethylene Glycol) Blend Membranes Formed in Different Coagulation Media

Novel Mussel-Inspired Zwitterionic Hydrophilic Polymer to Boost Membrane Water-Treatment Performance

Effect of Perfluorosulfonic Acid(PFSA)Content on the Performance of Polyvinyl Chloride-Perfluorosulfonic Acid(PVC-PFSA)Hollow Fiber Blend Ultrafiltration Membrane

Fabrication of a Low‐cost Nano‐sio2/pvc Composite Ultrafiltration Membrane and Its Antifouling Performance

Green and sustainable method of manufacturing anti-fouling zwitterionic polymers-modified poly(vinyl chloride) ultrafiltration membranes