Abstract:An in-situ reaction controlled non-solvent induced phase separation (RC-NIPS) method was developed to tailor the morphology of polyvinyl chloride (PVC)/styrene-maleic anhydride (SMA) grafting polyethylene glycol (PEG) (SMA-g-PEG) blend ultrafiltration (UF) membrane. Herein, PVC and SMA was dissolved in dimethylacetamide (DMAc) solvent to prepare a casting solution (16 wt.% polymer concentration) at 50 °C. Subsequently, PEG (20 kDa) as an additive and reactant was added to the casting solution at a mass ratio of PEG to the polymer 1/1 wt./wt. to enhance the hydrophilicity and mechanical elongation of the membrane. Results demonstrated that the casting solution with PVC/SMA = 3/1 wt./wt. was an entirely compatible system. The viscosity of the casting solution with adding PEG gradually increased from 692 mPa s to1880 mPa s at the initial stage and 4780 mPa s at 42 h, then rose sharply to 27,320 mPa s at 84 h. This behavior was ascribed to the esterification reaction between PEG and SMA, leading to pre-gelation and gelation of the system. Whereafter, SMA-g-PEG graft polymers were obtained. Meanwhile, the degree of grafting (DG) increased from 0.40% at 12 h of the reaction to 2.61% at 42 h. Afterwards, a phase inversion using water as coagulation was used to prepare PVC/SMA-g-PEG blend membrane after a certain time of the esterification reaction. It was found that the morphology of resultant membranes systematically changed from asymmetric structure with a dense top layer and finger-like sublayer at the initial stage to a dense layer with a fully sponge-like structure after 18–42 h reaction. The PVC/SMA-g-PEG membrane obtained after the reaction of 42 h demonstrated better hydrophilicity, high pure water permeance and excellent toughness due to the internal plasticization of water molecules. The membrane also exhibited a high BSA rejection (>95%) and fouling recovery rate (FRR) (85.9%). Our work provides some insights on tailoring the UF membrane structure and simultaneously enhancing permeability, antifouling performance and toughness.

Study of poly(vinyl chloride)/polyether sulphone co-blend ultrafiltration membrane

Improved Antifouling Properties of Polyvinyl Chloride Blend Membranes by Novel Phosphate Based-Zwitterionic Polymer Additive

Preparation of Positively-Charged Blend PVC/PEI Ultrafiltration Membranes with Crosslink Structure for Dye/Salt Separation

Compatibility Properties of PVC/PES and Its Impact on Co-blend Ultrafiltration Membrane

Synthesis of PVC-b-PEG Copolymer and Its Modification Effect on PVC Microfiltration Membrane

Fabrication anddye-salt separation of positively charged PVC/PEI composite nanofiltration membranes

Influence of Blending Ratio and Polymer Concentration on Miscibility of PVC/PVB and Property & Structure of Flat Ultra-Filtration Membrane

Membranes of poly (vinyl butyral) (PVB) or cationic PVB (CPVB) blended with poly (vinylidene fluoride) (PVDF) prepared by a nonsolvent induced phase separation method: Miscibility and hydrophilicity

Improved permeability and antifouling properties of polyvinyl chloride ultrafiltration membrane via blending sulfonated polysulfone

Poly(vinyl chloride) (PVC) hollow fiber ultrafiltration membranes prepared from PVC/additives/solvent

Enhanced Permeation and Antifouling Performance of Polyvinyl Chloride (PVC) Blend Pluronic F127 Ultrafiltration Membrane by Using Salt Coagulation Bath (SCB)

Morphology and Performance of Polyvinylidene Fluoride/Perfluorosulphonic Acid Hollow Fibre Ultrafiltration Blend Membranes

pH-Responsive Poly(vinyl chloride) Ultrafiltration Membranes Modified by Poly(vinyl chloride)-Poly(acrylic acid) Block Copolymers

Preparation and characterization of PVDF-P(PEGMA-r-MMA) ultrafiltration blend membranes via simplified blend method

Improved Antifouling Property of Poly(Ether Sulfone) Ultrafiltration Membrane Through Blending with Poly(Vinyl Alcohol)

Enhanced Permeability and Fouling-Resistant Capacity of Poly(vinylidene Fluoride) Ultrafiltration Membrane Based on the PPG-co-PEG-co-PPG Copolymer with Two Hydrophobic Terminals and One Hydrophilic Intermediate.

Effect of Perfluorosulfonic Acid(PFSA)Content on the Performance of Polyvinyl Chloride-Perfluorosulfonic Acid(PVC-PFSA)Hollow Fiber Blend Ultrafiltration Membrane

Primary study of novel poly(acrylic sodium)/poly(ether sulfone) composite ultrafiltration membranes (I) the preparation of composite membrane

Overview of Research Progress at Home on Development of Polyethersulfone(PES)Based Ultrafiltration Membrane

Tailoring the micro-structure of PVC/SMA-g-PEG blend ultrafiltration membrane with simultaneously enhanced hydrophilicity and toughness by in situ reaction-controlled phase inversion

Study on Preparation and Performance of Modified Polyvinyl Chloride-co-vinyl Acetate Microfiltration Membranes